logo

Epoxy Coatings

AY&B Epoxy Resin

General Purpose High performance Epoxy Resin

Used for: Altex Epoxy Resin may be mixed with either Altex Microballoons, or General Purpose Thickener to provide site mix fairing, gap filling glue and coving compounds.

 

  • Easy mixing  -  4 : 1 ratio by volume
  • Excellent cure characteristics with a good “tail” - mixed resin retains good flow throughout its pot life
  • Low viscosity with excellent wetting properties
  • Ideally packaged for Marine and Industrial use
  • Excellent stir in wetting of fairing and glue fillers and extenders
  • Cures well at low temperatures
  • Good flow characteristics with low viscosity minimizes air entrapment
  • Low odour

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Altra~Bond 3094

Altra~Bond 3094® is a two component, Strontium Chromate based epoxy primer designed for use on aluminium structures, sheets and extrusions and galvanised substrates. It has

  • Excellent adhesion and anti- corrosive properties
  • Fast dry to recoat
  • Compatibility with high performance epoxy and urethane systems

Altra~Bond 3094® is ideal as

  • A primer for aluminium topsides, alloy hulls and a general primer for trailed alloy boats
  • A primer for the exterior of petrol and bulk “dolphin” tanks
  • A primer for signwriting on alloy surfaces
  • An excellent general purpose aviation primer

 

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Altra~Lock 576

Altra~Lock® 576 is designed for use as a surface  sealer, conditioner and strengthener for porous substrates. It is especially useful in penetrating and saturating corroded surfaces where crevice corrosion cannot be treated by convention preparation methods.

May be overcoated with a wide range of build and/or finish coats.

 

Altra~Lock® 576 is a rapid cure and low temperature cure sealer which may be applied to a wide variety of  substrates such as:

Residual rust

Degraded or new concrete

Fibre reinforced cement

Asbestos cement

Timbers

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Altra~Shield 2000

Altra~Shield® 2000 is a high performance, multi-purpose high build epoxy coating available in a wide range of  tinted pastel colours.

Altra~Shield® 2000 is recommended for use:

  • On general exterior structural steel where an economical and aesthetic pleasing high performance finish is required.
  • Superior colour stability in exterior exposures as compared to other types of epoxy coatings
  • On concrete floors in service areas such as workshops and factories
  • Use as a deck coating, incorporating Non Skid Particles on Charter and Passenger vessels

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Altra~Shield WB-V Primer Finish

Made to Order or imported lines subject to availability.

Altra~Shield® WB-V is a two pack low VOC waterborne epoxy. The cured film presents a non-yellowing finish with high surface hardness and excellent flexibility. It exhibits excellent adhesion and water resistance, and is tolerant of application over damp surfaces. 

Self-priming over concrete, plaster and fibre cement substrates

  • Very good abrasion resistance
  • Excellent solvent resistance (when fully cured)
  • Excellent resistance to alkalis
  • Fair resistance to acids
  • Resistant to common CIP chemicals & typical dairy processing by-product exposures as follows:
    • Nitric Acid 5% - 15 hr watch-glass - pass*
    • Sodium Hydroxide 5% - 26 hr watch-glass - pass*
    • Lactic Acid 5% - 26 hr watch-glass - pass*

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet 

Carboguard 1340

Penetrating primer/sealer for use on concrete substrates and Carboline Pyrocrete Fireproofing products. It performs extremely well in sealing cementitious surfaces and is designed to receive a variety of different generic types of finish coats.

Some recommended uses of 1340 include the use as a curing compound or form release agent. When applied to “green” concrete it will retard the escape of moisture during the cure period.

It is also excellent for use as a form release coating on plywood or steel forms.

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Carboguard 2929

Proprietary cross-linking epoxy-acrylic gloss finish

Fast cure iso-cyanate-free epoxy-acrylic gloss coating for industrial and marine and off-shore applications where use of polyurethane coatings is banned or undesirable.

  • Isocyanate free
  • Early through-curing
  • Excellent colour and gloss retention with good chalking resistance
  • Lead and chrome-free colour range
  • Good chemical resistance
  • Excellent durability

 

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Carboguard 504

Carboguard® 504 is an inert non-inhibitive anti-corrosive modified polyamide cured epoxy primer.

  • Excellent primer for water and many aqueous chemicals immersion service when top-coated with an approved finish
  • Excellent adhesion to difficult substrates
  • Excellent holding primer
  • Excellent corrosion resistance
  • Complies with AS/NZS 3750.13 (2 pack epoxy primer), Types 1, 2 & 3.
  • Good abrasion resistance
  • Very good aged re-coatability
  • Resists splash and spillage or fumes of a wide range of chemicals
  • Easy application by brush, roller or spray
  • Ideal tie-coat over inorganic zincs
  • Versatile - can be used on most substrates under many different types of topcoat
  • Long pot-life
  • Excellent maintenance touch-up primer for hand-cleaned substrates

A user-friendly primer for epoxy or polyurethane systems in environments not suited to zinc primers due to acidic or alkaline fallout or splash & spill.

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Carboguard 635

An all purpose epoxy coating that has a variety of attributes including low temperature cure, surface tolerance, fast recoat times, moisture tolerance during application and cure, and excellent corrosion protection.

Carboguard 635 can be used direct to metal as a corrosion resistant primer or as an intermediate coating over primers.

It is suitable for both maintenance and new construction projects due to its excellent surface wetting characteristics and quick cure to handling.

It may also be used for immersion in both fresh or salt (marine) water.

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Carboguard 635 HAR

A rapid cure to topcoat epoxy with high abrasion resistance along with other valuable attributes including:

  • low-temperature cure
  • surface tolerance
  • fast recoat times
  • moisture tolerance during application and cure
  • excellent corrosion protection.

Carboguard 635 HAR can be used direct to metal as a corrosion resistant primer or as an intermediate coating over other primers. It may also be used for immersion in fresh or salt water exposures, and exhibits exceptional abrasion resistance and toughness.

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Carboguard 635 thinned 50% - sealer

Availability :

View More Product Data Sheet 

Carboguard 636

A highly versatile multi-purpose Phenalkamine Epoxy High Build coating.

Carboguard® 636 is an advanced technology coating suited to marine and industrial applications and suitable for atmospheric and many immersion exposures. The DTM properties make Carboguard® 636 a versatile coating in maintenance and new work applications. Syntactic foam modification gives Carboguard® 636 unique thermal shock resistance and flexibility

  • Marine systems - below the waterline, and fresh water systems
  • AS4020 Potable Water Approval for Haze Grey & Grey/White colours only.
  • Vast range of industrial environments
  • Very good flexibility – resists chipping and aged embrittlement
  • Lighter weight – 13% lighter than most similar coatings
  • Versatile, surface tolerant coating suitable for water jet cleaned surfaces
  • Tolerant to surface dampness - particularly when brush applied
  • Good thermal qualities; excellent for use under insulation to 120ºC
  • Good adhesion to tight rust - especially when used in conjunction with Rustbond® or Altra~Lock 576
  • Self-priming (DTM) for many applications
  • Fast dry to recoat and excellent dry to handling
  • Low temperature cure to below freezing; -5°C

 

Availability :- New Zealand

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Carboguard 640

Made to Order or imported lines subject to availability.

Carboguard® 640 is a high performance, two-component, modified phenalkamine, chemically cured, immersion grade epoxy barrier coating

Carboguard® 640 is an ideal high build coating for any service or structure, marine or industrial, where water or corrosion resistance is required.

Carboguard® 640 has excellent proven long-term service case histories for marine hull externals, above & below water, and as a lining for hydro penstocks and gates and similar permanently immersed structures.

Carboguard® 640 is the barrier coating of choice under Altex Sea~Barrier™ 1000, 3000 and Alloy 100Plus antifoulings

 

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Carboguard 690

High performance, surface tolerant epoxy that has excellent resistance to water and wastewater exposures. This coating exhibits outstanding moisture tolerance during application, low temperature cure capability, and very fast cure response for quick return to service.

  • Fully tintable epoxy high build
  • Suitable for all industrial and marine environments.
  • Carboguard 690 is also certified for use in both food processing and potable water storage and reticulation

Food Processing

NZ AsureQuality assessed & passed for food/beverage including dairy farm & factory non-incidental contact. Ref: H3108

 

Potable Water Approval – AS 4020:2005

Australian Water Quality Centre

Carboguard 690 White*        Reference: 130243-2009-CSR-1

Carboguard 690 N53 Bl/Gr*  Reference: 130243-2009-CSR-2

AMS Laboratories

Carboguard 690 N35 Lt. Gr* Reference: AMS 1316537A

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Carboguard 690 GF

Phenalkamine Epoxy with Glass Flake Additive to increase chemical, abrasion & thermal shock resistance

High performance, surface tolerant epoxy that has excellent resistance to water and wastewater exposures. This coating exhibits outstanding moisture tolerance during application, low temperature cure capability, and very fast cure response for quick return to service. Can be used on structural steel, piping, tankage, and equipment exposed to industrial or marine environments.

It can also be used in immersion service for salt water, process water (non-potable) and waste water treatment projects

  • Glass Flake Reinforced
  • Increased chemical, abrasion & thermal shock resistance
  • Suitable for service under insulation (CUI) up to 150°C – 1 coat at 150 microns DFT
  • High solids, low VOC
  • High build (200 microns)
  • Low temperature cure -7°C (20°F), Fast cure response

Available in a range of standard and tintable colours.

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Carboguard 690 Non-Skid

Phenalkamine Epoxy with Non-Skid Additive

High performance, surface tolerant epoxy that has excellent resistance to water and wastewater exposures. This coating exhibits outstanding moisture tolerance during application, low temperature cure capability, and very fast cure response for quick return to service.

Can be used as required on decks, walkways etc exposed to industrial or marine environments. It can also be used in splash & immersion service in salt water, process water (non-potable) and waste water treatment projects.

Two grades of Non Skid Particles (Medium & Coarse) are available.

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Carboguard 695 PM

Made to Order or imported lines subject to availability. Certified handlers only.

Carboguard 695 PM is a solventless, epoxy surfacer or patching mortar that is used to:

Fuel & Other Tanks: Transition between floor-wall chine areas, lapwelded plates, rivets, etc. It is typically used with a reinforced mat system specifically designed to comply with API RP652 for thick-film tank bottom lining repairs.

It is suitable for exposures in water, crude oil, aromatic distillates, and unblended gasolines. It is typically applied by broadknife, spatula, trowel, brush, or other suitable tool that allows heavy applications and smoothing procedures.

Excellent surfacer / patching mortar for concrete tanks & floors. Provides a rapid return to service screed for repairing flooring in high chemical exposure industrial environments.

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Carboguard 696 HBE

Made to Order or imported lines subject to availability. 

Carboguard® 696 HBE is a phenalkamine cured high solids, syntactic foam modified high build epoxy coating

Carboguard® 696 HBE is designed for single coat application as a penstock lining to film thicknesses typically ranging between 400 & 600 microns using correctly equipped industry standard airless spray equipment of sufficient capacity.

Carboguard® 696 HBE is suitable for service in immersion, on buried structures, and on high wear surfaces in atmospheric exposure

  • High Build Single Coat – 0.4mm to 0.6 mm in a single coat
  • Extensive case history in hydro penstocks and scroll casings
  • Potable water compliant formulation (refer Carboguard 696 UHBE)
  • Positive cure, even at low temperatures
  • Abrasion resistant
  • Unique flexibilised formulation imparts excellent impact resistance
  • May be used on buried structures, structures immersed in fresh or salt water, and for atmospheric exposure
  • Suitable for use with cathodic protection systems – impressed current or anode types
  • Low density of 1.09 – heavy duty protection with minimal added weight

 

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Carbomastic 615

This high performance epoxy coating exhibits outstanding moisture and surface tolerance during application, low temperature cure capability, and very fast cure response for quick return to service. This makes Carbomastic 615 eminently suitable for maintenance repaint work in marginal conditions and where surface preparation is less than ideal.

It contains an inert flake reinforcement (micaceous iron oxide) to enhance film strength and performance.

  • High solids, low VOC
  • Low temperature cure
  • Excellent wetting properties
  • Excellent surface tolerance
  • Excellent moisture tolerance (application)
  • Fast cure response

Suitable for immersion service in fresh or salt water after 60 minute cure @ 24°C

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Carbotherm 551

Waterborne two component epoxy with insulative properties

Availability :

View More Product Data Sheet 

Carboxane 2000

Carboxane 2000 is a premium, ultra-durable coating that provides outstanding gloss and colour retention for exterior exposures.

Carboxane 2000 combines the chemical resistant properties of epoxies and polysiloxanes with the weathering characteristics of premium acrylic-polyurethanes. This tightly cross-linked film results in a finish with outstanding barrier properties and weathering performance.

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Carboxane 2000 Satin

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet 

Rustbond

Rustbond is a cross-linked penetrating primer/sealer with excellent wetting properties. It is highly flexible with good chemical and solvent resistance, and will accept a variety of topcoats.

Recommended use as primer/sealer for marginally prepared steel and over old coatings. The excellent wetting properties allows it to penetrate rust and discontinuities in existing coatings and provide a firm anchorage for a variety of topcoats.

The thixotropic character reduces run off, ensuring that the edges of existing coatings are encapsulated thus reducing undercutting and peeling.

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Offline

* Sorry, we aren’t online at the moment. Please fill out the form below and we will get back to you as soon as possible.