Pulp Paper

Altra~Lock® 576 is designed for use as a surface  sealer, conditioner and strengthener for porous substrates. It is especially useful in penetrating and saturating corroded surfaces where crevice corrosion cannot be treated by convention preparation methods.

May be overcoated with a wide range of build and/or finish coats.

Altra~Lock® 576 is a rapid cure and low temperature cure sealer which may be applied to a wide variety of  substrates such as:

Residual rust

Degraded or new concrete

Fibre reinforced cement

Asbestos cement

Timbers

Proprietary cross-linking epoxy-acrylic gloss finish

Fast cure iso-cyanate-free epoxy-acrylic gloss coating for industrial and marine and off-shore applications where use of polyurethane coatings is banned or undesirable.

• Isocyanate free
• Early through-curing
• Excellent colour and gloss retention with good chalking resistance
• Lead and chrome-free colour range
• Good chemical resistance
• Excellent durability

Carboguard® 504 is an inert non-inhibitive anti-corrosive modified polyamide cured epoxy primer.

• Excellent primer for water and many aqueous chemicals immersion service when top-coated with an approved finish
• Excellent adhesion to difficult substrates
• Excellent holding primer
• Excellent corrosion resistance
• Complies with AS/NZS 3750.13 (2 pack epoxy primer), Types 1, 2 & 3.
• Good abrasion resistance
• Very good aged re-coatability
• Resists splash and spillage or fumes of a wide range of chemicals
• Easy application by brush, roller or spray
• Ideal tie-coat over inorganic zincs
• Versatile - can be used on most substrates under many different types of topcoat
• Long pot-life
• Excellent maintenance touch-up primer for hand-cleaned substrates

A user-friendly primer for epoxy or polyurethane systems in environments not suited to zinc primers due to acidic or alkaline fallout or splash & spill.

A rapid cure to topcoat epoxy with high abrasion resistance along with other valuable attributes including:

• low-temperature cure
• surface tolerance
• fast recoat times
• moisture tolerance during application and cure
• excellent corrosion protection.

Carboguard 635 HAR can be used direct to metal as a corrosion resistant primer or as an intermediate coating over other primers. It may also be used for immersion in fresh or salt water exposures, and exhibits exceptional abrasion resistance and toughness.

A highly versatile multi-purpose Phenalkamine Epoxy High Build coating.

Carboguard® 636 is an advanced technology coating suited to marine and industrial applications and suitable for atmospheric and many immersion exposures. The DTM properties make Carboguard® 636 a versatile coating in maintenance and new work applications. Syntactic foam modification gives Carboguard® 636 unique thermal shock resistance and flexibility

• Marine systems - below the waterline, and fresh water systems
• AS4020 Potable Water Approval for Haze Grey & Grey/White colours only.
• Vast range of industrial environments
• Very good flexibility – resists chipping and aged embrittlement
• Lighter weight – 13% lighter than most similar coatings
• Versatile, surface tolerant coating suitable for water jet cleaned surfaces
• Tolerant to surface dampness - particularly when brush applied
• Good thermal qualities; excellent for use under insulation to 120ºC
• Good adhesion to tight rust - especially when used in conjunction with Rustbond® or Altra~Lock 576
• Self-priming (DTM) for many applications
• Fast dry to recoat and excellent dry to handling
• Low temperature cure to below freezing; -5°C

High performance, surface tolerant epoxy that has excellent resistance to water and wastewater exposures. This coating exhibits outstanding moisture tolerance during application, low temperature cure capability, and very fast cure response for quick return to service.

• Fully tintable epoxy high build
• Suitable for all industrial and marine environments.
• Carboguard 690 is also certified for use in both food processing and potable water storage and reticulation

Food Processing

NZ AsureQuality assessed & passed for food/beverage including dairy farm & factory non-incidental contact. Ref: H3108

Potable Water Approval – AS 4020:2005

Australian Water Quality Centre

Carboguard 690 White*        Reference: 130243-2009-CSR-1

Carboguard 690 N53 Bl/Gr*  Reference: 130243-2009-CSR-2

AMS Laboratories

Carboguard 690 N35 Lt. Gr* Reference: AMS 1316537A

Phenalkamine Epoxy with Glass Flake Additive to increase chemical, abrasion & thermal shock resistance

High performance, surface tolerant epoxy that has excellent resistance to water and wastewater exposures. This coating exhibits outstanding moisture tolerance during application, low temperature cure capability, and very fast cure response for quick return to service. Can be used on structural steel, piping, tankage, and equipment exposed to industrial or marine environments.

It can also be used in immersion service for salt water, process water (non-potable) and waste water treatment projects

• Glass Flake Reinforced
• Increased chemical, abrasion & thermal shock resistance
• Suitable for service under insulation (CUI) up to 150°C – 1 coat at 150 microns DFT
• High solids, low VOC
• High build (200 microns)
• Low temperature cure -7°C (20°F), Fast cure response

Available in a range of standard and tintable colours.

Phenalkamine Epoxy with Non-Skid Additive

High performance, surface tolerant epoxy that has excellent resistance to water and wastewater exposures. This coating exhibits outstanding moisture tolerance during application, low temperature cure capability, and very fast cure response for quick return to service.

Can be used as required on decks, walkways etc exposed to industrial or marine environments. It can also be used in splash & immersion service in salt water, process water (non-potable) and waste water treatment projects.

Two grades of Non Skid Particles (Medium & Coarse) are available.

Made to Order or imported lines subject to availability. Certified handlers only.

Carboguard 695 PM is a solventless, epoxy surfacer or patching mortar that is used to:

Fuel & Other Tanks: Transition between floor-wall chine areas, lapwelded plates, rivets, etc. It is typically used with a reinforced mat system specifically designed to comply with API RP652 for thick-film tank bottom lining repairs.

It is suitable for exposures in water, crude oil, aromatic distillates, and unblended gasolines. It is typically applied by broadknife, spatula, trowel, brush, or other suitable tool that allows heavy applications and smoothing procedures.

Excellent surfacer / patching mortar for concrete tanks & floors. Provides a rapid return to service screed for repairing flooring in high chemical exposure industrial environments.

Made to Order or imported lines subject to availability. 

Carboguard® 696 HBE is a phenalkamine cured high solids, syntactic foam modified high build epoxy coating

Carboguard® 696 HBE is designed for single coat application as a penstock lining to film thicknesses typically ranging between 400 & 600 microns using correctly equipped industry standard airless spray equipment of sufficient capacity.

Carboguard® 696 HBE is suitable for service in immersion, on buried structures, and on high wear surfaces in atmospheric exposure

• High Build Single Coat – 0.4mm to 0.6 mm in a single coat
• Extensive case history in hydro penstocks and scroll casings
• Potable water compliant formulation (refer Carboguard 696 UHBE)
• Positive cure, even at low temperatures
• Abrasion resistant
• Unique flexibilised formulation imparts excellent impact resistance
• May be used on buried structures, structures immersed in fresh or salt water, and for atmospheric exposure
• Suitable for use with cathodic protection systems – impressed current or anode types
• Low density of 1.09 – heavy duty protection with minimal added weight

This high performance epoxy coating exhibits outstanding moisture and surface tolerance during application, low temperature cure capability, and very fast cure response for quick return to service. This makes Carbomastic 615 eminently suitable for maintenance repaint work in marginal conditions and where surface preparation is less than ideal.

It contains an inert flake reinforcement (micaceous iron oxide) to enhance film strength and performance.

• High solids, low VOC
• Low temperature cure
• Excellent wetting properties
• Excellent surface tolerance
• Excellent moisture tolerance (application)
• Fast cure response

Suitable for immersion service in fresh or salt water after 60 minute cure @ 24°C

High gloss polyurethane finish with exceptional weathering performance characteristics.

Used extensively in virtually every market sector, including marine exposure, Carbothane 134 HG provides a smooth, durable finish that has superior resistance to corrosion, abrasion and chemical exposure.

• Specialised UV protection designed for Australian and New Zealand exposures
• Highly recoatable, with minimum preparation requirements
• The high solids (70%) formulation creates a very cost effective coating

Carbotherm 3300 is a ceramic blend insulative composite coating formulated using a high temperature resistant acrylic binder.

It is ideally suited as a protective heat barrier to shield personnel from hot surfaces. It also inhibits heat transfer into or out of a structure. Its insulative properties keep structures exposed to solar radiation significantly cooler. It can be used to minimize or eliminate sweating of pipes or other operating equipment

• Excellent thin-film insulation
• Unique formula provides superior coverage during application
• Protects personnel from hot surfaces
• Multi-purpose interior/exterior coating
• Insulation provides anti-condensation properties
• Easy to use

Zero VOC; Low odour at application

Made to Order or imported lines subject to availability.

Carbozinc 11 WB is a water-based inorganic zinc rich primer that protects steel galvanically, eliminating subfilm corrosion. It meets VOC regulations while providing the proven performance of silicate zinc rich technology. It may be used as a primer under many different types of topcoats

• Excellent corrosion protection
• High zinc loading per square metre
• Zero VOC
• Good resistance to salting
• Fast curing, quick handling
• Excellent application characteristics (less likely to pump packing or tip plug)
• Meets Class B slip coefficient* and creep testing criteria for use on faying surfaces.
• Conforms to AS/NZS 3750.15 Type 3

NEW 4:1 Ratio

Low VOC organic zinc epoxy steel primer with quick cure-to-topcoat characteristics for in-shop  applications and quick turnaround requirements in the field. Carbozinc 858 has very good adhesion and undercutting resistance and is excellent for use as a corrosion resistant primer for a variety of applications

• Meets SSPC Paint System 20
• Fully complies with AS 3750.9:1994 Type 2 Organic Zinc Rich
• Low temperature cure down to 2°C
• Protects against undercutting corrosion
• May be applied with standard airless or conventional spray equipment
• VOC compliant to current AIM regulations

A very economic, two-component, high solids, zinc rich epoxy primer formulated for the protection of properly prepared steel substrates.

Carbozinc 859 EZ2 can be applied by conventional, airless, or plural component spray. Recommended where a high performance, highly corrosion resistant zinc primer is desired.

Typical applications include structural steel, tanks, piping, equipment and other miscellaneous parts in industrial, offshore or architectural projects.

Chem~Bar 900™ is specifically formulated to protect metal or masonry surfaces exposed to weather, water or chemicals.

Chem~Bar 900™ may be used to protect structural steel, tanks, pipes and equipment a vast range of industries.

It's recoatable properties, highly anti-corrosive formulation and ease of application make it an ideal coating for both maintenance and new work.

• Pulp and Paper Industry
• Chemical Process Industry
• Sewage and Waste Water Plants
• Water Tanks
• Refineries
• Fertiliser Plants
• Marine Installations
• Bridges
• Power Projects
• Containers
• Shipping

Metal Spray Sealer - a traditional Vinyl sealer used in accordance with ASNZ2312 Zinc Metalspray systems, as well as a single package high performance aluminium filled vinyl-acrylic finish suitable for use as a general purpose aluminium finish.

Chem~Bar 900™ Aluminium may be used in all atmospheric exposures where traditional aluminium finishes may be employed; including:

• Pulp and Paper Industry
• Chemical Process Industry
• Sewage and Waste Water Plants
• Water Tank & Silo Exteriors
• Refineries
• Fertiliser Plants
• Marine Installations
• Bridges
• Power Projects
• Containers
• Shipping

E~Line 379® is a high gloss, high performance, two component, chemically cured polyaspartic urethane designed for use in areas where maximum gloss and colour retention are required.

E~Line 379® will provide excellent gloss and colour retention as well as resistance to moderate to severe corrosive environments for:

• Transportation industry
• Chemical processing industry
• Pulp and paper industry
• Dairy industry
• Bridges and storage tanks
• Light colours and clear may be used as anti-graffiti coatings due to their excellent solvent resistance - refer also to Altex Graffiti Remover and Easy~Clean SX Additive
• Outstanding abrasion resistance
• Excellent durability due to high flexibility and toughness
• Exceptional tolerance to marginal application conditions
• Exceptional retention of cosmetic properties due to high UV resistance

Made to Order or imported lines subject to availability. 

Single package, water-based, flexible mastic fire protective coating for cables and cable trays.

A water based mastic that can be applied to electrical cables to retard fire propagation. Once applied, it meets code and insurance requirements for interior and exterior use. It provides a hard and flexible surface that will not dust, flake, or spall

Made to Order or imported lines subject to availability. 

A glass flake-filled coating with dense cross-linking that exhibits excellent overall chemical resistance to a variety of aggressive chemicals. Glass reinforcement provides added abrasion resistance, permeation resistance and internal reinforcement.

Phenoline® 1205 exhibits very good acid resistance. Excellent for lining tanks or pipes in process facilities where hot water or abrasive conditions exist. Also used as a primary or secondary containment lining for a variety of aggressive chemicals

• Excellent resistance to acids, caustics, ethanol, gasoline, jet fuels and solvents
• Excellent abrasion resistance
• Excellent thermal shock resistance
• Excellent resistance to deionized or demineralised water up to 82°C
• Excellent resistance to crude oil, brine or water up to 93°C

Made to Order or imported lines subject to availability.

Phenoline 311 is a holding primer designed for application in storage / tanks prior to application of the selected tank coating.

Featuring Low Temperature Cure, Potable Water approval (AS4020 / ANSI/NSF ) and extended recoat times this Novalac / Phenalkamine primer provides exceptional corrosion resistance and adhesion properties.

Made to Order or imported lines subject to availability. 

High solids modified novalac epoxy, with excellent low temperature cure and outstanding chemical resistance.

Provides immersion grade service for a vast range of chemicals (refer Data Sheet)  in a wide range of industries:

Wastewater

Petrochemical

Industrial manufacturing / processing

Chemical transport

Made to order or imported product subject to avalability.

A high performance, immersion grade coating system which has excellent resistance to wet/dry cycling conditions at elevated temperatures

• Temperature resistance to 204°C (400°F)
• Very good flexibility
• Excellent overall chemical resistance
• Very good abrasion resistance
• Easily applied by spray
• Acceptable for use over stainless steels

Used in conjunction with Thermaline 400 Primer

Single package silicone finish.

High-performance finish for areas exposed to extreme temperatures. Suitable for service from 204°C-538°C (400°F-1000°F) and surges to 650°C. Requires heat curing.

Resistant to severe thermal shock

Provides outstanding long-term performance when applied over Carbozinc inorganic zinc primers

Air-dries to touch (full film formation properties occurs after heat curing)

Air-dried silicone acrylic coating available in Aluminium and suitable for high temperature exposures up to 232°C. Air-drying characteristics allow for faster handling of in-shop applications than with other high-temperature coatings.

Heat cure above 149°C is recommended and will impart added strength and integrity to the coating.

Made to order or imported product subject to avalability.

This is an extreme performance coating for hot, cryogenic and cycling exposures. Thermaline Heat Shield contains a unique blend of plate-like reinforcing pigments fortified with an inert polymeric matrix. The resulting film provides an outstanding barrier against corrosives and harsh exposures typically seen in elevated temperature environments. This versatile coating is ideal for all piping, vessels and equipment operating from cryogenic conditions up to 1200°F. It is particularly well suited to prevent corrosion under insulated equipment/piping for both carbon steel substrates and stainless steels. This fortified coating has superior shop handling properties over standard silicone coatings (see Curing). It is recommended for CS-6 and SS-5 systems of NACE SP0198 Standard Practice for coatings to control corrosion under insulation (CUI).