logo

Tank Lining Coatings

Carbocrete 522

Made to Order or imported lines subject to availability.

Fibre Reinforced Cementitious Mortar

A spray-grade, economical, shrinkage-compensated, repair mortar, and surfacing compound that exhibits excellent bond strength to concrete. It is ideally suited for substrate resurfacing of deteriorated concrete and is typically topcoated with Carboline’s lining systems. Various lining systems are available. Each system provides excellent corrosion protection against targeted exposures, especially to acid attack due to wet hydrogen sulfide environment found in wastewater

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Carboguard 510 SG

Made to Order or imported lines subject to availability.

A spray-grade, economical, epoxy-based repair mortar, patching and surfacing compound that exhibits excellent bond strength to concrete and other masonry surfaces. It is ideally suited for resurfacing deteriorated concrete in wastewater environment. Topcoated with Carboline’s lining systems provides protection from acid attack from H2S or MIC. Unique spraygrade (SG) formulation speeds application properties for quick turnaround projects

  • Epoxy modification improves chemical resistance for wastewater environment
  • Zero VOC
  • Water based, low odour
  • Excellent film strength, abrasion, and impact resistance
  • Easily topcoated to provide additional chemical resistance or appearance
  • Self-priming over concrete
  • Aggregate reinforced

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Carboguard 636 (potable water only)

High performance immersion grade epoxy that is designed as a liner for potable water tanks. This coating exhibits moisture tolerance during application, low temperature cure capability, and fast cure response for quick return to service.
Product is self-priming on steel and is normally applied in two coats. Formulated for application at 120 to 180 microns DFT per coat for potable use.

  • Very good flexibility – resists chipping and aged embrittlement
  • Lighter weight – 13% lighter than most similar coatings
  • Versatile surface tolerant coating
  • AS/NZS 4020 Potable Water Approval (see "Approvals NZ/AU" section)
  • Lower viscosity allows application at higher solids (less thinning) and reduced VOC at application
  • Fast dry to recoat
  • Low temperature cure to below freezing; -5°C
  • Reduced HAPS and Low VOC

 

Availability :- New Zealand

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Carboguard 636 XT

A multi-purpose, advanced technology coating suited to marine and industrial applications. Suitable for atmospheric and many immersion exposures. The DTM properties make it a versatile coating in maintenance and new work applications. Syntactic foam modification gives it unique thermal shock resistance and flexibility.

Link

 

Availability :

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Carboguard 636 XT GF

A glass-flake filled, multi-purpose,advanced technology coating suited to marine and industrial applications. Suitable for atmospheric and many immersion exposures. The DTM properties make it a versatile coating in maintenance and new work applications. Syntactic foam modification gives it unique thermal shock resistance and flexibility. Glass flake reinforcement enhances film strength,
impact resistance and barrier properties.

Availability :

View More Product Data Sheet 

Carboguard 696 HBE

Made to Order or imported lines subject to availability. 

Suitable for single coat applications in areas such as a penstock lining at film thicknesses ranging between 400 and 1500 microns. Suitable for service in various immersion environments including industrial wastewater, slurry tanks, sea or fresh water, on buried structures, and on high wear surfaces in atmospheric exposure.

  • High film builds in a single coat – 0.4mm to 1.5mm
  • Extensive case history in hydro penstocks & scroll casings, along with industrial wastewater processing
  • Positive cure, even at low temperatures
  • Highly abrasion resistant
  • Unique flexibilised formulation imparts excellent impact resistance
  • May be used on buried structures, structures immersed in fresh or salt water, and for atmospheric exposure
  • Suitable for use with cathodic protection systems – impressed current or anode types
  • Easy application qualities using properly heavy-duty airless spray equipment

 

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Filler #50

Graded silica blend for epoxy putty / mortar mixes

Availability :

View More NZ Safety Data Sheet Aus. Safety Data Sheet

Phenoline 1205

Made to Order or imported lines subject to availability. 

A glass flake-filled coating with dense cross-linking that exhibits excellent overall chemical resistance to a variety of aggressive chemicals. Glass reinforcement provides added abrasion resistance, permeation resistance and internal reinforcement.

Phenoline® 1205 exhibits very good acid resistance. Excellent for lining tanks or pipes in process facilities where hot water or abrasive conditions exist. Also used as a primary or secondary containment lining for a variety of aggressive chemicals

  • Excellent resistance to acids, caustics, ethanol, gasoline, jet fuels and solvents
  • Excellent abrasion resistance
  • Excellent thermal shock resistance
  • Excellent resistance to deionized or demineralised water up to 82°C
  • Excellent resistance to crude oil, brine or water up to 93°C

 

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Phenoline 353 LT

Made to Order or imported lines subject to availability. 

High solids modified novalac epoxy, with excellent low temperature cure and outstanding chemical resistance.

Provides immersion grade service for a vast range of chemicals (refer Data Sheet)  in a wide range of industries:

 

Wastewater

Petrochemical

Industrial manufacturing / processing

Chemical transport

 

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Phenoline Tank Shield

 

Made to Order or imported lines subject to availability. 

Amine Adduct cured epoxy. This product is a solvent-free, high performance epoxy coating designed as an internal tank, valve and pipe lining for chemical or other commodity storage.

The product is blush resistant and is typically applied at film thicknesses of 500-625 microns or thicker as needed (tank floors). It will withstand exposures typically seen in the oil and gas industries; crude oils and fuels. It is resistant to NGL condensates, produced water, brines, and industrial process water.

Availability :

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Phenoline Tank Shield FP

This product is a solvent-free, high performance epoxy coating specifically designed as a pit
filling primer with ideal flow properties allowing it to wet-out and fill moderate to severe pitting on
steel tank bottoms. It's unique formula allows simple batch mixing for ease of application. With an
appropriate lining, it can handle exposures typically seen in the oil and gas industries. It is resistant
to crude oil, NGL condensates, produced water, brines, and industrial process water.

Availability :

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Plasite 4550

PLASITE 4550 is a 100% solids, reinforced, premium novolac epoxy coating for internal tank lining. It is resistant to a broad range of chemicals such as fuels, salts, alkalis, strong inorganic acids, some solvents, sour crude oil and 98% sulfuric acid.

Availability :

View More Product Data Sheet 

Plasite 9570

Plasite 9570 is a highly resistant film for chemical tank lining service. Specifically formulated for
excellent abrasion resistance while retaining temperature, chemical and other physical properties to
provide greater release properties to aid in the prevention of product hang-up or bridging problems.

Availability :

View More Product Data Sheet 

Reactamine 760 HB

Made to Order or imported lines subject to availability.

Environmentally friendly, advanced hybrid technology, plural-component applied coating used as a lining for water, wastewater, manholes, penstocks, dam gates, pipelines and other aggressive immersion applications. Provides protection against microbiologically induced corrosion (MIC) and hydrogen sulfide corrosion found in wastewater treatment service. Ultra high build product designed to be applied at high thickness in one coat application. 

Availability :

View More Product Data Sheet NZ Safety Data Sheet 

Reactamine Joint Seal

Made to Order or imported lines subject to availability. 

Reactamine Joint Seal FC is a 2-component 100% solids, polyurea-based joint sealant that is self-leveling and cures in approximately 30 minutes. It works equally well with asphalt and concrete and protects interior horizontal concrete expansion and control joints from spalling, chipping and breakdown. This product can be applied at temperatures ranging from -18° to 65°C and possesses excellent chemical resistance, water resistance and thermal stability at both high and low temperatures

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Semstone 870

Semstone 870 is a high performance, vinyl ester lining system designed for concrete. Semstone 870 is formulated to be more flexible than typical vinyl esters to tolerate more concrete movement. It is a semi-leveling coating which may be applied as an aggregate filled and/or reinforced coating system. Semstone 870 is specially formulated to withstand some of industry’s most aggressive chemicals, including a broad range of organic chemicals.

Availability :

View More Product Data Sheet 

Splash-Zone A788

Solvent-free patching compound used for repairing pits, cracks and voids in steel, concrete, wood and other surfaces. Has the unique ability to be mixed, applied and cured underwater.
 

MTO. Imported line subject to availability. 

Availability :

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Offline

* Sorry, we aren’t online at the moment. Please fill out the form below and we will get back to you as soon as possible.