Made to Order or imported lines subject to availability.
This solvent borne intumescent is applied to steel for fire ratings up to 120 minutes, and is designed to be used in interior systems. (typically overcoated with Pro~Seal Intumescent Seal Coat and polyurethane finish coats as appropriate)
Availability :- New Zealand
View More Product Data Sheet NZ Safety Data SheetMade to Order or imported lines subject to availability.
Single package, water-based, flexible mastic fire protective coating for cables and cable trays.
A water based mastic that can be applied to electrical cables to retard fire propagation. Once applied, it meets code and insurance requirements for interior and exterior use. It provides a hard and flexible surface that will not dust, flake, or spall
Availability :- New Zealand- Australia
View More Product Data SheetMade to Order or imported lines subject to availability.
Key Benefits Summary
• Water based intumescent coating suitable for internal use on structural steelwork for up to 120 minute fire resistance
• Easier to apply product for greater efficency on site with improved smooth matt finish
• Compatible with a full range of Nullifire primers and top seals
• Very low VOC
Availability :
View More Product Data Sheet NZ Safety Data SheetMade to Order or imported lines subject to availability.
SC802 Intumescent Basecoat is a white thin film intumescent coating for the fire protection of internal structural steelwork.
SC802 provides effective structural fire protection, for steelwork, up to a 60 minute fire rating.
SC802 is designed for on-site application
BENEFITS
Availability :
View More Product Data Sheet NZ Safety Data SheetMade to Order or imported lines subject to availability. Certified Applicators Only.
Nullifire SC902 is a fast track on or off-site, low VOC, one coat high build system capable of providing up to 2 hours protection in a single coat
Conventional intumescent coating systems for 120 FRR that may take 7 days to complete can be completed in just 24 hours using Nullifire SC902
Availability :- New Zealand
View More Product Data Sheet NZ Safety Data SheetA single pack, fast dry sealer designed to offer weathering protection to solvent borne intumescent coatings.
Pro~Seal promotes the cure of intumescent coatings, while at the same time it provides a water barrier to prevent damage to the film.
Once cured, this seal coat reduces solvent absorption when overcoated, therefore reducing the risk of solvent entrapment.
May be overcoated with both single component finish coats and two component polyurethanes, in waterbased or solvent borne formulations.
Availability :
View More Product Data Sheet NZ Safety Data SheetMade to order or imported product subject to avalability.
Cementitious inorganic fireproofing formulation
Recommended uses for the fire protection of structural steel, bulkheads, and upgrading the fire resistance of existing concrete. Recommended areas of application are refineries, petrochemical, pharmaceutical facilities, pulp and paper mills, offshore platforms, nuclear and conventional power plants, factories, warehouses, institutional and biomedical facilities.
Unique crack-free formulation
Availability :- New Zealand- Australia
View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data SheetCementitious inorganic polymer fireproofing formulation.
Single powder component mixed with clean, potable water before it is used in application. Recommended uses for the fire protection of structural steel, bulkheads, and upgrading the fire resistance of any existing concrete. Recommended areas of application are petrochemical plants, pharmaceutical facilities, power plants, schools & hospitals, noise abatement and air plenums
Availability :- New Zealand- Australia
View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data SheetAvailability :
View MoreMade to order or imported product subject to avalability.
Cementitious, noncombustible, inorganic fireproofing supplied as a single powder component that is mixed with clean, potable water prior to application
Southwest Type 5GP is intended for application to interior structural columns, beams, joists, decks, walls, roofs, girders, floors and pre-cast concrete units. It is tested and certified for fire resistance ratings up to 4 hours
Ready to use – No site additives required
Availability :- New Zealand- Australia
View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data SheetMade to order or imported product subject to avalability.
A two component, epoxy based, thermally activated, intumescent coating for the fire protection of structural steel.
Thermo-Lag® 3000 SP is designed to fireproof steelwork for up to a 4 hour fire rating, depending on the design. The recommended use for this product is fireproofing of steel beams, columns, tubes, pipes, vessel skirts, bulkheads, underdecks and electrical raceways
Availability :- New Zealand- Australia
View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data SheetA two component, epoxy based, thermally activated, intumescent coating which is primarily spray applied directly over Thermo-Lag® 3000 series EPFP.
Thermo-Lag® 3002 provides a hard, durable duplex system that allows for the reduction of coating thickness in a jet fire environment as well as enhanced environmental resistance
Availability :- New Zealand- Australia
View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data SheetAn epoxy intumescent fireproofing for commercial and light industrial applications. It was specifically designed with an advanced formulation to provide 1-3 hour cellulosic fire protection for structural steel beams, I-section columns, tubular columns and pipes without the need for reinforcing mesh. It provides a fast curing, aesthetically pleasing fire protection solution and is rated for both exterior and interior applications.
Availability :
View More Product Data Sheet