logo

Commercial and Architecture

Altra~Bond 3094

Altra~Bond 3094® is a two component, Strontium Chromate based epoxy primer designed for use on aluminium structures, sheets and extrusions and galvanised substrates. It has

  • Excellent adhesion and anti- corrosive properties
  • Fast dry to recoat
  • Compatibility with high performance epoxy and urethane systems

Altra~Bond 3094® is ideal as

  • A primer for aluminium topsides, alloy hulls and a general primer for trailed alloy boats
  • A primer for the exterior of petrol and bulk “dolphin” tanks
  • A primer for signwriting on alloy surfaces
  • An excellent general purpose aviation primer

 

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Altra~Lock 576

Altra~Lock® 576 is designed for use as a surface  sealer, conditioner and strengthener for porous substrates. It is especially useful in penetrating and saturating corroded surfaces where crevice corrosion cannot be treated by convention preparation methods.

May be overcoated with a wide range of build and/or finish coats.

 

Altra~Lock® 576 is a rapid cure and low temperature cure sealer which may be applied to a wide variety of  substrates such as:

Residual rust

Degraded or new concrete

Fibre reinforced cement

Asbestos cement

Timbers

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Altra~Shield 2000

Altra~Shield® 2000 is a high performance, multi-purpose high build epoxy coating available in a wide range of  tinted pastel colours.

Altra~Shield® 2000 is recommended for use:

  • On general exterior structural steel where an economical and aesthetic pleasing high performance finish is required.
  • Superior colour stability in exterior exposures as compared to other types of epoxy coatings
  • On concrete floors in service areas such as workshops and factories
  • Use as a deck coating, incorporating Non Skid Particles on Charter and Passenger vessels

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Altra~Shield WB-V Primer Finish

Made to Order or imported lines subject to availability.

Altra~Shield® WB-V is a two pack low VOC waterborne epoxy. The cured film presents a non-yellowing finish with high surface hardness and excellent flexibility. It exhibits excellent adhesion and water resistance, and is tolerant of application over damp surfaces. 

Self-priming over concrete, plaster and fibre cement substrates

  • Very good abrasion resistance
  • Excellent solvent resistance (when fully cured)
  • Excellent resistance to alkalis
  • Fair resistance to acids
  • Resistant to common CIP chemicals & typical dairy processing by-product exposures as follows:
    • Nitric Acid 5% - 15 hr watch-glass - pass*
    • Sodium Hydroxide 5% - 26 hr watch-glass - pass*
    • Lactic Acid 5% - 26 hr watch-glass - pass*

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet 

Carboguard 1340

Penetrating primer/sealer for use on concrete substrates and Carboline Pyrocrete Fireproofing products. It performs extremely well in sealing cementitious surfaces and is designed to receive a variety of different generic types of finish coats.

Some recommended uses of 1340 include the use as a curing compound or form release agent. When applied to “green” concrete it will retard the escape of moisture during the cure period.

It is also excellent for use as a form release coating on plywood or steel forms.

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Carboguard 2929

Proprietary cross-linking epoxy-acrylic gloss finish

Fast cure iso-cyanate-free epoxy-acrylic gloss coating for industrial and marine and off-shore applications where use of polyurethane coatings is banned or undesirable.

  • Isocyanate free
  • Early through-curing
  • Excellent colour and gloss retention with good chalking resistance
  • Lead and chrome-free colour range
  • Good chemical resistance
  • Excellent durability

 

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Carboguard 504

Carboguard® 504 is an inert non-inhibitive anti-corrosive modified polyamide cured epoxy primer.

  • Excellent primer for water and many aqueous chemicals immersion service when top-coated with an approved finish
  • Excellent adhesion to difficult substrates
  • Excellent holding primer
  • Excellent corrosion resistance
  • Complies with AS/NZS 3750.13 (2 pack epoxy primer), Types 1, 2 & 3.
  • Good abrasion resistance
  • Very good aged re-coatability
  • Resists splash and spillage or fumes of a wide range of chemicals
  • Easy application by brush, roller or spray
  • Ideal tie-coat over inorganic zincs
  • Versatile - can be used on most substrates under many different types of topcoat
  • Long pot-life
  • Excellent maintenance touch-up primer for hand-cleaned substrates

A user-friendly primer for epoxy or polyurethane systems in environments not suited to zinc primers due to acidic or alkaline fallout or splash & spill.

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Carboguard 635

An all purpose epoxy coating that has a variety of attributes including low temperature cure, surface tolerance, fast recoat times, moisture tolerance during application and cure, and excellent corrosion protection.

Carboguard 635 can be used direct to metal as a corrosion resistant primer or as an intermediate coating over primers.

It is suitable for both maintenance and new construction projects due to its excellent surface wetting characteristics and quick cure to handling.

It may also be used for immersion in both fresh or salt (marine) water.

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Carboguard 635 TMS Seal Coat

Availability :

View More Product Data Sheet 

Carboguard 636

A highly versatile multi-purpose Phenalkamine Epoxy High Build coating.

Carboguard® 636 is an advanced technology coating suited to marine and industrial applications and suitable for atmospheric and many immersion exposures. The DTM properties make Carboguard® 636 a versatile coating in maintenance and new work applications. Syntactic foam modification gives Carboguard® 636 unique thermal shock resistance and flexibility

  • Marine systems - below the waterline, and fresh water systems
  • Vast range of industrial environments
  • Very good flexibility – resists chipping and aged embrittlement
  • Lighter weight – 13% lighter than most similar coatings
  • Versatile, surface tolerant coating suitable for water jet cleaned surfaces
  • Tolerant to surface dampness - particularly when brush applied
  • Good thermal qualities; excellent for use under insulation to 120ºC
  • Good adhesion to tight rust - especially when used in conjunction with Rustbond® or Altra~Lock 576
  • Self-priming (DTM) for many applications
  • Fast dry to recoat and excellent dry to handling
  • Low temperature cure to below freezing; -5°C

 

Availability :- New Zealand

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Carboguard 640

Made to Order or imported lines subject to availability.

Carboguard® 640 is a high performance, two-component, modified phenalkamine, chemically cured, immersion grade epoxy barrier coating

Carboguard® 640 is an ideal high build coating for any service or structure, marine or industrial, where water or corrosion resistance is required.

Carboguard® 640 has excellent proven long-term service case histories for marine hull externals, above & below water, and as a lining for hydro penstocks and gates and similar permanently immersed structures.

Carboguard® 640 is the barrier coating of choice under Altex Sea~Barrier™ 1000, 3000 and Alloy 100Plus antifoulings

 

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Carboguard 690

High performance, surface tolerant epoxy that has excellent resistance to water and wastewater exposures. This coating exhibits outstanding moisture tolerance during application, low temperature cure capability, and very fast cure response for quick return to service.

  • Fully tintable epoxy high build
  • Suitable for all industrial and marine environments.
  • Carboguard 690 is also certified for use in both food processing and potable water storage and reticulation

Food Processing

NZ AsureQuality assessed & passed for food/beverage including dairy farm & factory non-incidental contact. Ref: H3108

 

Potable Water Approval – AS 4020:2005

Australian Water Quality Centre

Carboguard 690 White*        Reference: 130243-2009-CSR-1

Carboguard 690 N53 Bl/Gr*  Reference: 130243-2009-CSR-2

AMS Laboratories

Carboguard 690 N35 Lt. Gr* Reference: AMS 1316537A

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Carboquick 200

This fast cure high build polyaspartic coating provides excellent corrosion protection as well as long term weatherability in just one coat.

It can be applied direct to metal (DTM) at 150 to 250 µms dry film thickness (DFT) to eliminate the need for typical primers and/or intermediate coats. This significantly speeds up the painting process, saves labor, and saves money without sacrificing performance. If even better corrosion protection is desired it can be applied over our time proven Carbozinc or Carboguard primers.

Availability :

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Carbothane 130 Clear Coat

Clear Aliphatic Acrylic Polyurethane with HALS and UV absorber technology

Thin film, high gloss finish with exceptional weathering performance characteristics. Used extensively in virtually all industrial markets including marine exposures, Carbothane 130 Clear Coat provides a smooth, durable finish that provides superior resistance to colour fade of base-coats, corrosion, abrasion and chemical exposure.

  • High solids, low VOC content
  • Excellent weatherability
  • Superior impact and abrasion resistance
  • Excellent chemical resistance
  • Excellent resistance to graffiti removers

Carbothane 10 Clear is frequently applied over conventional, pigmented polyurethane fionish coats to provide an optimum surface for anti graffiti management.

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Carbothane 133 LH

Aliphatic Acrylic-Polyester Polyurethane Satin Finish

High build, low sheen finish that has excellent resistance to corrosion, chemicals and abrasion. Suitable for application over a number of Carboline primers and intermediates, this material provides very good weathering performance in a broad range of colours

  • Outstanding performance properties in both mild and aggressive environments
  • High build; suitable for many two-coat systems
  • Approved for use in food & dairy processing plants
  • Application by spray, brush or roller
  • Indefinite recoatability
  • VOC compliant to current AIM regulations

 

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Carbothane 134 HG

High gloss polyurethane finish with exceptional weathering performance characteristics.

Used extensively in virtually every market sector, including marine exposure, Carbothane 134 HG provides a smooth, durable finish that has superior resistance to corrosion, abrasion and chemical exposure.

  • Specialised UV protection designed for Australian and New Zealand exposures
  • Highly recoatable, with minimum preparation requirements
  • The high solids (70%) formulation creates a very cost effective coating

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Carboxane 2000

Carboxane 2000 is a premium, ultra-durable coating that provides outstanding gloss and colour retention for exterior exposures.

Carboxane 2000 combines the chemical resistant properties of epoxies and polysiloxanes with the weathering characteristics of premium acrylic-polyurethanes. This tightly cross-linked film results in a finish with outstanding barrier properties and weathering performance.

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Carboxane 2000 Satin

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet 

Carbozinc 11

Time-tested corrosion resistant primer that protects steel galvanically in the harshest environments. For over four decades, Carbozinc 11 (CZ 11) has been the industry standard for high-performance inorganic zinc protection on steel structures worldwide

 

  • CZ 11 meets Class B slip co-efficient and creep testing criteria for use on faying surfaces
  • Rapid cure. Dry to handle in 45 minutes at 16°C and 50% relative humidity.
  • Low temperature cure down to -18°C.
  • High zinc loading.
  • Meets FDA requirements in grey color.
  • Available in ASTM D520, Type II zinc version.
  • Very good resistance to salting.
  • May be applied with standard airless or conventional spray equipment.
  • Complies with the composition and performance requirements of:
    • AS/NZS 3750.15, Type 4
    • AS 4848.1:2006 Single Coat Inorganic Zinc Silicate

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Carbozinc 11 WB

Made to Order or imported lines subject to availability.

Carbozinc 11 WB is a water-based inorganic zinc rich primer that protects steel galvanically, eliminating subfilm corrosion. It meets VOC regulations while providing the proven performance of silicate zinc rich technology. It may be used as a primer under many different types of topcoats

 

  • Excellent corrosion protection
  • High zinc loading per square metre
  • Zero VOC
  • Good resistance to salting
  • Fast curing, quick handling
  • Excellent application characteristics (less likely to pump packing or tip plug)
  • Meets Class B slip coefficient* and creep testing criteria for use on faying surfaces.
  • Conforms to AS/NZS 3750.15 Type 3

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Carbozinc 858

NEW 4:1 Ratio

Low VOC organic zinc epoxy steel primer with quick cure-to-topcoat characteristics for in-shop  applications and quick turnaround requirements in the field. Carbozinc 858 has very good adhesion and undercutting resistance and is excellent for use as a corrosion resistant primer for a variety of applications

 

  • Meets SSPC Paint System 20
  • Fully complies with AS 3750.9:1994 Type 2 Organic Zinc Rich
  • Low temperature cure down to 2°C
  • Protects against undercutting corrosion
  • May be applied with standard airless or conventional spray equipment
  • VOC compliant to current AIM regulations

Availability :

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Carbozinc 859 EZ2

A very economic, two-component, high solids, zinc rich epoxy primer formulated for the protection of properly prepared steel substrates.

Carbozinc 859 EZ2 can be applied by conventional, airless, or plural component spray. Recommended where a high performance, highly corrosion resistant zinc primer is desired.

Typical applications include structural steel, tanks, piping, equipment and other miscellaneous parts in industrial, offshore or architectural projects.

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Easy~Roll Defoaming Additive

Easy~Roll Defoamer is an additive specifically for use in Altex & carboline Polyurethane finish coats.

Easy~Roll is incorporated into the base component prior to catalysing. It enhances the rolling properties and assists in removing bubbling and foam.

Availability :

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

E~Line 379

E~Line 379® is a high gloss, high performance, two component, chemically cured polyaspartic urethane designed for use in areas where maximum gloss and colour retention are required.

E~Line 379® will provide excellent gloss and colour retention as well as resistance to moderate to severe corrosive environments for:

  • Transportation industry
  • Chemical processing industry
  • Pulp and paper industry
  • Dairy industry
  • Bridges and storage tanks
  • Light colours and clear may be used as anti-graffiti coatings due to their excellent solvent resistance - refer also to Altex Graffiti Remover and Easy~Clean SX Additive
  • Outstanding abrasion resistance
  • Excellent durability due to high flexibility and toughness
  • Exceptional tolerance to marginal application conditions
  • Exceptional retention of cosmetic properties due to high UV resistance

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

E~Line 949

E~Line® 949 is a fast cure, economical, high gloss, aliphatic polyurethane designed for use in areas where good gloss and colour retention are required.

E~Line® 949 is ideal for use where a polyurethane finish is specified and where economy and rapid drying are desirable. It will provide good gloss and colour retention as well as resistance to moderate to severe corrosive environments for:

  • Structural Steel
  •  Shop application
  • Chemical processing industry
  • Pulp and paper industry
  • Dairy industry
  • Bridges and storage tanks

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Firetex FX2003

Made to Order or imported lines subject to availability. 

This solvent borne intumescent is applied to steel for fire ratings up to 120 minutes, and is designed to be used in interior systems. (typically overcoated with Pro~Seal Intumescent Seal Coat and polyurethane finish coats as appropriate)

 

  • Single pack, rapid touch dry
  • Builds up to 800µms DFT per coat per day in standard conditions
  • Applied using industry standard airless spray equipment
  • Competitive loadings and pricing structures

Availability :- New Zealand

View More Product Data Sheet NZ Safety Data Sheet 

High Build Rust Barrier

Advantages:

  • Inhibits corrosion of steel-higher levels of ZP than other alkyd primers
  • Capable of high film build per coat
  • Lead free
  • Superior performance on power and hand tool cleaned surfaces
  • Easy application by brush, roller or spray
  • Excellent flow and levelling
  • Can be used on marine topsides

Approvals:

  • MAF Meat, Fish and Game Division
  • AS4089-1993 : Type 1 and 2 primer Meets and exceeds AS4089-1993* in particular adhesion and performance clauses:5.5.4; 5.5.5; 5.5.6

* Independently assessed by NZ DSIR (1992), Report No. SCPP 92/1160T
Meets requirements of AHB 522-1994 (Auckland Harbour Bridge maintenance)

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet 

Intumastic 285

Made to Order or imported lines subject to availability. 

Single package, water-based, flexible mastic fire protective coating for cables and cable trays.

A water based mastic that can be applied to electrical cables to retard fire propagation. Once applied, it meets code and insurance requirements for interior and exterior use. It provides a hard and flexible surface that will not dust, flake, or spall

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Isotal Enamel

Isotal is a premium quality alkyd gloss enamel which is designed to protect and give good appearance to:

  • Properly primed steel and other metal surfaces
  • Tank exteriors
  • Bridges and pipes
  • Commercial Marine exterior areas such as freeboards, decks, houses and superstructures
  • Commercial Marine interior areas such as engine rooms, passageways and equipment

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Isotal Undercoat

Isotal Undercoat is a premium quality alkyd undercoat which is normally used under Isotal Enamel on properly primed surfaces. It can be used in areas such as:

  • Properly primed masonry, steel and other metal surfaces
  • Marine exterior areas such as freeboards, decks, houses and superstructures
  • Marine interior areas such as engine rooms, passageways and equipment
  • Wooden structures
  • Tie coat over aged enamel systems prior to re-finish coating

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Multi~Bond Primer

Multi~Bond Primer is a premium quality primer designed to be used on:.

 

  • Applied directly to suitably prepared steel, galvanised steel, wood and GRP
  • Above water - overcoated with a sandable undercoat (Altex Isotal Undercoat) and normally topcoated with Isotal Enamel
  • Below water – in mulitple coats as part of a marine protective system where it is normally overcoated with Sea~Barrier™ 1000 or 3000 anti-fouling
  • Agricultural equipment
  • On site touch-up work-handrails etc
  • Restoration of timber joinery

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Pre~Fab

Pre~Fab Steel Shop Primer is a fast dry, economical, primer designed for use in engineering fabrication shops.

Advantages:   Fast dry allows rapid handling of coated steel. It is suitable as a stand-alone coating in mild interior environments and provides good protection to structural steel in moderate exterior environments when topcoated with compatible alkyd or acrylic coatings.

Limitations of Use: Not designed for extended exterior exposure.

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet 

RIPO

Rust Inhibiting Protective Oil is a drying “wetting oil” pre-treatment, for use on hand or power tool cleaned surfaces and sometimes with brush blasted surfaces, prior to application of (usually)  High Build Rust Barrier.

RIPO forms a water resistant film and is useful in protecting steel from condensation corrosion, as encountered in particular on:

  • Interior of vehicle doors and body panels
  • Underside of surfaces on appliances, such as freezers and washing machines
  • Marine topsides
  • Excellent rust treatment as part of a single pack coating system on; Agricultural machinery and various pieces of equipment, trailers, structural steel

Use RIPO as the first stage in restoring items as listed above. Once cured apply High Build Rust Barrier, followed by Isotal Enamel to achieve long term protective and cosmetic properties.

 

 

 

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Offline

* Sorry, we aren’t online at the moment. Please fill out the form below and we will get back to you as soon as possible.