logo

Commercial Marine

Altra~Bond 3094

Altra~Bond 3094® is a two component, Strontium Chromate based epoxy primer designed for use on aluminium structures, sheets and extrusions and galvanised substrates. It has

  • Excellent adhesion and anti- corrosive properties
  • Fast dry to recoat
  • Compatibility with high performance epoxy and urethane systems

Altra~Bond 3094® is ideal as

  • A primer for aluminium topsides, alloy hulls and a general primer for trailed alloy boats
  • A primer for the exterior of petrol and bulk “dolphin” tanks
  • A primer for signwriting on alloy surfaces
  • An excellent general purpose aviation primer

 

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Altra~Lock 576

Altra~Lock® 576 is designed for use as a surface  sealer, conditioner and strengthener for porous substrates. It is especially useful in penetrating and saturating corroded surfaces where crevice corrosion cannot be treated by convention preparation methods.

May be overcoated with a wide range of build and/or finish coats.

 

Altra~Lock® 576 is a rapid cure and low temperature cure sealer which may be applied to a wide variety of  substrates such as:

Residual rust

Degraded or new concrete

Fibre reinforced cement

Asbestos cement

Timbers

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Altra~Shield 2000

Altra~Shield® 2000 is a high performance, multi-purpose high build epoxy coating available in a wide range of  tinted pastel colours.

Altra~Shield® 2000 is recommended for use:

  • On general exterior structural steel where an economical and aesthetic pleasing high performance finish is required.
  • Superior colour stability in exterior exposures as compared to other types of epoxy coatings
  • On concrete floors in service areas such as workshops and factories
  • Use as a deck coating, incorporating Non Skid Particles on Charter and Passenger vessels

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Altra~Shield WB-V Primer Finish

Made to Order or imported lines subject to availability.

Altra~Shield® WB-V is a two pack low VOC waterborne epoxy. The cured film presents a non-yellowing finish with high surface hardness and excellent flexibility. It exhibits excellent adhesion and water resistance, and is tolerant of application over damp surfaces. 

Self-priming over concrete, plaster and fibre cement substrates

  • Very good abrasion resistance
  • Excellent solvent resistance (when fully cured)
  • Excellent resistance to alkalis
  • Fair resistance to acids
  • Resistant to common CIP chemicals & typical dairy processing by-product exposures as follows:
    • Nitric Acid 5% - 15 hr watch-glass - pass*
    • Sodium Hydroxide 5% - 26 hr watch-glass - pass*
    • Lactic Acid 5% - 26 hr watch-glass - pass*

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet 

Altra~Zinc 605

Altra~Zinc® 605 is a high performance, two component, reinforced  zinc-rich primer designed for use as a cathodic primer for protecting steel exposed to a variety of environments.

Altra~Zinc® 605 is an ideal, rapid dry zinc primer for use on most mild steel fabricated equipment where it's reinforced  binder system is required including:

  • Heavy Machinery
  • Conveyors, Pipework etc
  • Structural Steel
  • Original Equipment Manufacturing (OEM)

 

Limitations of Use:

  • Do not topcoat with alkyd coatings
  • Not suitable for solvent, chemical or fresh water immersion service

 

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Carboguard 504

Carboguard® 504 is an inert non-inhibitive anti-corrosive modified polyamide cured epoxy primer.

  • Excellent primer for water and many aqueous chemicals immersion service when top-coated with an approved finish
  • Excellent adhesion to difficult substrates
  • Excellent holding primer
  • Excellent corrosion resistance
  • Complies with AS/NZS 3750.13 (2 pack epoxy primer), Types 1, 2 & 3.
  • Good abrasion resistance
  • Very good aged re-coatability
  • Resists splash and spillage or fumes of a wide range of chemicals
  • Easy application by brush, roller or spray
  • Ideal tie-coat over inorganic zincs
  • Versatile - can be used on most substrates under many different types of topcoat
  • Long pot-life
  • Excellent maintenance touch-up primer for hand-cleaned substrates

A user-friendly primer for epoxy or polyurethane systems in environments not suited to zinc primers due to acidic or alkaline fallout or splash & spill.

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Carboguard 635 HAR

A rapid cure to topcoat epoxy with high abrasion resistance along with other valuable attributes including:

  • low-temperature cure
  • surface tolerance
  • fast recoat times
  • moisture tolerance during application and cure
  • excellent corrosion protection.

Carboguard 635 HAR can be used direct to metal as a corrosion resistant primer or as an intermediate coating over other primers. It may also be used for immersion in fresh or salt water exposures, and exhibits exceptional abrasion resistance and toughness.

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Carboguard 635 TMS Seal Coat

Availability :

View More Product Data Sheet 

Carboguard 636

A highly versatile multi-purpose Phenalkamine Epoxy High Build coating.

Carboguard® 636 is an advanced technology coating suited to marine and industrial applications and suitable for atmospheric and many immersion exposures. The DTM properties make Carboguard® 636 a versatile coating in maintenance and new work applications. Syntactic foam modification gives Carboguard® 636 unique thermal shock resistance and flexibility

  • Marine systems - below the waterline, and fresh water systems
  • Vast range of industrial environments
  • Very good flexibility – resists chipping and aged embrittlement
  • Lighter weight – 13% lighter than most similar coatings
  • Versatile, surface tolerant coating suitable for water jet cleaned surfaces
  • Tolerant to surface dampness - particularly when brush applied
  • Good thermal qualities; excellent for use under insulation to 120ºC
  • Good adhesion to tight rust - especially when used in conjunction with Rustbond® or Altra~Lock 576
  • Self-priming (DTM) for many applications
  • Fast dry to recoat and excellent dry to handling
  • Low temperature cure to below freezing; -5°C

 

Availability :- New Zealand

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Carboguard 640

Made to Order or imported lines subject to availability.

Carboguard® 640 is a high performance, two-component, modified phenalkamine, chemically cured, immersion grade epoxy barrier coating

Carboguard® 640 is an ideal high build coating for any service or structure, marine or industrial, where water or corrosion resistance is required.

Carboguard® 640 has excellent proven long-term service case histories for marine hull externals, above & below water, and as a lining for hydro penstocks and gates and similar permanently immersed structures.

Carboguard® 640 is the barrier coating of choice under Altex Sea~Barrier™ 1000, 3000 and Alloy 100Plus antifoulings

 

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Carboguard 690

High performance, surface tolerant epoxy that has excellent resistance to water and wastewater exposures. This coating exhibits outstanding moisture tolerance during application, low temperature cure capability, and very fast cure response for quick return to service.

  • Fully tintable epoxy high build
  • Suitable for all industrial and marine environments.
  • Carboguard 690 is also certified for use in both food processing and potable water storage and reticulation

Food Processing

NZ AsureQuality assessed & passed for food/beverage including dairy farm & factory non-incidental contact. Ref: H3108

 

Potable Water Approval – AS 4020:2005

Australian Water Quality Centre

Carboguard 690 White*        Reference: 130243-2009-CSR-1

Carboguard 690 N53 Bl/Gr*  Reference: 130243-2009-CSR-2

AMS Laboratories

Carboguard 690 N35 Lt. Gr* Reference: AMS 1316537A

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Carboguard 690 Non-Skid

Phenalkamine Epoxy with Non-Skid Additive

High performance, surface tolerant epoxy that has excellent resistance to water and wastewater exposures. This coating exhibits outstanding moisture tolerance during application, low temperature cure capability, and very fast cure response for quick return to service.

Can be used as required on decks, walkways etc exposed to industrial or marine environments. It can also be used in splash & immersion service in salt water, process water (non-potable) and waste water treatment projects.

Two grades of Non Skid Particles (Medium & Coarse) are available.

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Carboguard 695 PM

Made to Order or imported lines subject to availability. Certified handlers only.

Carboguard 695 PM is a solventless, epoxy surfacer or patching mortar that is used to:

Fuel & Other Tanks: Transition between floor-wall chine areas, lapwelded plates, rivets, etc. It is typically used with a reinforced mat system specifically designed to comply with API RP652 for thick-film tank bottom lining repairs.

It is suitable for exposures in water, crude oil, aromatic distillates, and unblended gasolines. It is typically applied by broadknife, spatula, trowel, brush, or other suitable tool that allows heavy applications and smoothing procedures.

Excellent surfacer / patching mortar for concrete tanks & floors. Provides a rapid return to service screed for repairing flooring in high chemical exposure industrial environments.

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Carbomastic 615 MIOX

This high performance epoxy coating exhibits outstanding moisture and surface tolerance during application, low temperature cure capability, and very fast cure response for quick return to service. This makes Carbomastic 615 eminently suitable for maintenance repaint work in marginal conditions and where surface preparation is less than ideal.

It contains an inert flake reinforcement (micaceous iron oxide) to enhance film strength and performance.

  • High solids, low VOC
  • Low temperature cure
  • Excellent wetting properties
  • Excellent surface tolerance
  • Excellent moisture tolerance (application)
  • Fast cure response

Suitable for immersion service in fresh or salt water after 60 minute cure @ 24°C

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Carbothane 134 HG

High gloss polyurethane finish with exceptional weathering performance characteristics.

Used extensively in virtually every market sector, including marine exposure, Carbothane 134 HG provides a smooth, durable finish that has superior resistance to corrosion, abrasion and chemical exposure.

  • Specialised UV protection designed for Australian and New Zealand exposures
  • Highly recoatable, with minimum preparation requirements
  • The high solids (70%) formulation creates a very cost effective coating

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Carbotherm 551

Waterborne two component epoxy with insulative properties

Availability :

View More Product Data Sheet 

Carbozinc 858

NEW 4:1 Ratio

Low VOC organic zinc epoxy steel primer with quick cure-to-topcoat characteristics for in-shop  applications and quick turnaround requirements in the field. Carbozinc 858 has very good adhesion and undercutting resistance and is excellent for use as a corrosion resistant primer for a variety of applications

 

  • Meets SSPC Paint System 20
  • Fully complies with AS 3750.9:1994 Type 2 Organic Zinc Rich
  • Low temperature cure down to 2°C
  • Protects against undercutting corrosion
  • May be applied with standard airless or conventional spray equipment
  • VOC compliant to current AIM regulations

Availability :

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Chem~Bar 3500

Chem~Bar™3500 Primer is a single pack steel primer designed for use in industrial and marine applications.

For atmospheric exposures, Chem~Bar 3500™Primer is normally topcoated with Chem~Bar 900™Finish.

 

Chem~Bar 3500™Primer may be:

  • Applied directly over steel or over zinc primers such as Carbozinc® 859 EZ2, Carbozinc® 858, Zinkex 100 or Carbozinc® 11.
  • Used on substrates other than steel, (consult Altex Coatings for specific recommendations.)

Chem~Bar 3500™Primer is used in the commercial marine sector as a:

  • barrier/seal coat over aged or incompatible/unknown antifoulings
  • as a tie coat over suitably prepared, aged epoxy coatings prior to application of the selected Sea~Barrier® antifouling
  • sealant to assist in the prevention of TBT leaching from an underlying antifouling coating - provided it is applied at a minimum dry film thickness of 80 microns (minimum 2 coats by roller).

It is normally overcoated with Sea~Barrier® 1000, 3000 or Sea~Barrier® Alloy 100 PLUS Anti-fouling.

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Chem~Bar 900

Chem~Bar 900™ is specifically formulated to protect metal or masonry surfaces exposed to weather, water or chemicals.

Chem~Bar 900™ may be used to protect structural steel, tanks, pipes and equipment a vast range of industries.

It's recoatable properties, highly anti-corrosive formulation and ease of application make it an ideal coating for both maintenance and new work.

  • Pulp and Paper Industry
  • Chemical Process Industry
  • Sewage and Waste Water Plants
  • Water Tanks
  • Refineries
  • Fertiliser Plants
  • Marine Installations
  • Bridges
  • Power Projects
  • Containers
  • Shipping

 

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Chem~Bar 900 Aluminium MS Sealer

Metal Spray Sealer - a traditional Vinyl sealer used in accordance with ASNZ2312 Zinc Metalspray systems, as well as a single package high performance aluminium filled vinyl-acrylic finish suitable for use as a general purpose aluminium finish.

Chem~Bar 900™ Aluminium may be used in all atmospheric exposures where traditional aluminium finishes may be employed; including:

  • Pulp and Paper Industry
  • Chemical Process Industry
  • Sewage and Waste Water Plants
  • Water Tank & Silo Exteriors
  • Refineries
  • Fertiliser Plants
  • Marine Installations
  • Bridges
  • Power Projects
  • Containers
  • Shipping

 

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Easy~Roll Defoaming Additive

Easy~Roll Defoamer is an additive specifically for use in Altex & carboline Polyurethane finish coats.

Easy~Roll is incorporated into the base component prior to catalysing. It enhances the rolling properties and assists in removing bubbling and foam.

Availability :

View More Product Data Sheet NZ Safety Data Sheet 

E~Line 949

E~Line® 949 is a fast cure, economical, high gloss, aliphatic polyurethane designed for use in areas where good gloss and colour retention are required.

E~Line® 949 is ideal for use where a polyurethane finish is specified and where economy and rapid drying are desirable. It will provide good gloss and colour retention as well as resistance to moderate to severe corrosive environments for:

  • Structural Steel
  •  Shop application
  • Chemical processing industry
  • Pulp and paper industry
  • Dairy industry
  • Bridges and storage tanks

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Isotal Enamel

Isotal is a premium quality alkyd gloss enamel which is designed to protect and give good appearance to:

  • Properly primed steel and other metal surfaces
  • Tank exteriors
  • Bridges and pipes
  • Commercial Marine exterior areas such as freeboards, decks, houses and superstructures
  • Commercial Marine interior areas such as engine rooms, passageways and equipment

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Isotal Undercoat

Isotal Undercoat is a premium quality alkyd undercoat which is normally used under Isotal Enamel on properly primed surfaces. It can be used in areas such as:

  • Properly primed masonry, steel and other metal surfaces
  • Marine exterior areas such as freeboards, decks, houses and superstructures
  • Marine interior areas such as engine rooms, passageways and equipment
  • Wooden structures
  • Tie coat over aged enamel systems prior to re-finish coating

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Multi~Bond Primer

Multi~Bond Primer is a premium quality primer designed to be used on:.

 

  • Applied directly to suitably prepared steel, galvanised steel, wood and GRP
  • Above water - overcoated with a sandable undercoat (Altex Isotal Undercoat) and normally topcoated with Isotal Enamel
  • Below water – in mulitple coats as part of a marine protective system where it is normally overcoated with Sea~Barrier™ 1000 or 3000 anti-fouling
  • Agricultural equipment
  • On site touch-up work-handrails etc
  • Restoration of timber joinery

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Phenoline 311

Made to Order or imported lines subject to availability.

Phenoline 311 is a holding primer designed for application in storage / tanks prior to application of the selected tank coating.

Featuring Low Temperature Cure, Potable Water approval (AS4020 / ANSI/NSF ) and extended recoat times this Novalac / Phenalkamine primer provides exceptional corrosion resistance and adhesion properties.

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

RIPO

Rust Inhibiting Protective Oil is a drying “wetting oil” pre-treatment, for use on hand or power tool cleaned surfaces and sometimes with brush blasted surfaces, prior to application of (usually)  High Build Rust Barrier.

RIPO forms a water resistant film and is useful in protecting steel from condensation corrosion, as encountered in particular on:

  • Interior of vehicle doors and body panels
  • Underside of surfaces on appliances, such as freezers and washing machines
  • Marine topsides
  • Excellent rust treatment as part of a single pack coating system on; Agricultural machinery and various pieces of equipment, trailers, structural steel

Use RIPO as the first stage in restoring items as listed above. Once cured apply High Build Rust Barrier, followed by Isotal Enamel to achieve long term protective and cosmetic properties.

 

 

 

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Rustbond

Rustbond is a cross-linked penetrating primer/sealer with excellent wetting properties. It is highly flexible with good chemical and solvent resistance, and will accept a variety of topcoats.

Recommended use as primer/sealer for marginally prepared steel and over old coatings. The excellent wetting properties allows it to penetrate rust and discontinuities in existing coatings and provide a firm anchorage for a variety of topcoats.

The thixotropic character reduces run off, ensuring that the edges of existing coatings are encapsulated thus reducing undercutting and peeling.

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Sea~Barrier 1000

Sea~Barrier® 1000 is a cost effective ablative antifouling coating, designed for commercial applications

It is recommended for use where a harder, economic and relaible semi-ablative antifouling is required.

 Sea~Barrier® 1000 is the ideal antifoul coating for:

  • In-shore commercial vessels and barges subject to light to medium duty
  • Marine farm equipment
  • Use on bottom flats and as a boottop in conjunction with Sea~Barrier® 3000 on critical areas

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Sea~Barrier 3000

Sea~Barrier® 3000  is a high performance, ablative antifouling coating and  is recommended for use where:

  • Superior ablative properties are required
  • Long term, well proven protection is desired

Sea~Barrier® 3000 is the ideal antifoul coating for both  Maintenance Docking and New Builds.

 

Sea~Barrier® 3000 is suitable for:

  • Barges
  • Tug Boats
  • Ferries
  • Charter Vessels
  • Fishing Vessels
  • Numerous other sea going vessels

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Sea~Barrier Alloy 100 PLUS/AU

Sea~Barrier® Alloy 100  Antifouling is an Aluminium Safe antifouling for all commercial vessels.

  • Available in NZ as Sea~Barrier® Alloy 100 PLUS
  • Available in Australia as Sea~Barrier® Alloy 100AU
  • New Formula! Supersedes standard Alloy 100 with higher volume solids and new biocide technologies.
  • Slime resistant
  • Available in three distinctive clean colours
  • Excellent for aluminium vessels and stern-drives
  • Tin free
  • Economical - 2 coats at 75 microns each giving superior performance over most competitor aluminium-safe anti-foulings
  • Proven performance in NZ and South Pacific waters.

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Sea~Barrier Altra

Sea~Barrier® Altra Antifouling is a new generation Silyl Acrylate formulation that protects hulls from marine growth though a self polishing hydrolysis action.

The silyl acrylate, cuprous oxide and co-biocide combination provides outstanding protection that exceeds normal cuprous oxide based formulations. Extensive testing has proven Sea~Barrier® Altra to be at the cutting edge of antifouling technology.

Availability :

View More Product Data Sheet NZ Safety Data Sheet 

Splash-Zone A788

Solvent-free patching compound used for repairing pits, cracks and voids in steel, concrete, wood and other surfaces. Has the unique ability to be mixed, applied and cured underwater.
 

MTO. Imported line subject to availability. 

Availability :

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Offline

* Sorry, we aren’t online at the moment. Please fill out the form below and we will get back to you as soon as possible.