logo

Petrochemical

Altra~Lock 576

Altra~Lock® 576 is designed for use as a surface  sealer, conditioner and strengthener for porous substrates. It is especially useful in penetrating and saturating corroded surfaces where crevice corrosion cannot be treated by convention preparation methods.

May be overcoated with a wide range of build and/or finish coats.

 

Altra~Lock® 576 is a rapid cure and low temperature cure sealer which may be applied to a wide variety of  substrates such as:

Residual rust

Degraded or new concrete

Fibre reinforced cement

Asbestos cement

Timbers

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Carboguard 635 HAR

A rapid cure to topcoat epoxy with high abrasion resistance along with other valuable attributes including:

  • low-temperature cure
  • surface tolerance
  • fast recoat times
  • moisture tolerance during application and cure
  • excellent corrosion protection.

Carboguard 635 HAR can be used direct to metal as a corrosion resistant primer or as an intermediate coating over other primers. It may also be used for immersion in fresh or salt water exposures, and exhibits exceptional abrasion resistance and toughness.

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Carboguard 635 thinned 50% - sealer

Availability :

View More Product Data Sheet 

Carboguard 636

A highly versatile multi-purpose Phenalkamine Epoxy High Build coating.

Carboguard® 636 is an advanced technology coating suited to marine and industrial applications and suitable for atmospheric and many immersion exposures. The DTM properties make Carboguard® 636 a versatile coating in maintenance and new work applications. Syntactic foam modification gives Carboguard® 636 unique thermal shock resistance and flexibility

  • Marine systems - below the waterline, and fresh water systems
  • Vast range of industrial environments
  • Very good flexibility – resists chipping and aged embrittlement
  • Lighter weight – 13% lighter than most similar coatings
  • Versatile, surface tolerant coating suitable for water jet cleaned surfaces
  • Tolerant to surface dampness - particularly when brush applied
  • Good thermal qualities; excellent for use under insulation to 120ºC
  • Good adhesion to tight rust - especially when used in conjunction with Rustbond® or Altra~Lock 576
  • Self-priming (DTM) for many applications
  • Fast dry to recoat and excellent dry to handling
  • Low temperature cure to below freezing; -5°C

 

Availability :- New Zealand

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Carboguard 690

High performance, surface tolerant epoxy that has excellent resistance to water and wastewater exposures. This coating exhibits outstanding moisture tolerance during application, low temperature cure capability, and very fast cure response for quick return to service.

  • Fully tintable epoxy high build
  • Suitable for all industrial and marine environments.
  • Carboguard 690 is also certified for use in both food processing and potable water storage and reticulation

Food Processing

NZ AsureQuality assessed & passed for food/beverage including dairy farm & factory non-incidental contact. Ref: H3108

 

Potable Water Approval – AS 4020:2005

Australian Water Quality Centre

Carboguard 690 White*        Reference: 130243-2009-CSR-1

Carboguard 690 N53 Bl/Gr*  Reference: 130243-2009-CSR-2

AMS Laboratories

Carboguard 690 N35 Lt. Gr* Reference: AMS 1316537A

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Carboguard 690 GF

Phenalkamine Epoxy with Glass Flake Additive to increase chemical, abrasion & thermal shock resistance

High performance, surface tolerant epoxy that has excellent resistance to water and wastewater exposures. This coating exhibits outstanding moisture tolerance during application, low temperature cure capability, and very fast cure response for quick return to service. Can be used on structural steel, piping, tankage, and equipment exposed to industrial or marine environments.

It can also be used in immersion service for salt water, process water (non-potable) and waste water treatment projects

  • Glass Flake Reinforced
  • Increased chemical, abrasion & thermal shock resistance
  • Suitable for service under insulation (CUI) up to 150°C – 1 coat at 150 microns DFT
  • High solids, low VOC
  • High build (200 microns)
  • Low temperature cure -7°C (20°F), Fast cure response

Available in a range of standard and tintable colours.

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Carboguard 690 Non-Skid

Phenalkamine Epoxy with Non-Skid Additive

High performance, surface tolerant epoxy that has excellent resistance to water and wastewater exposures. This coating exhibits outstanding moisture tolerance during application, low temperature cure capability, and very fast cure response for quick return to service.

Can be used as required on decks, walkways etc exposed to industrial or marine environments. It can also be used in splash & immersion service in salt water, process water (non-potable) and waste water treatment projects.

Two grades of Non Skid Particles (Medium & Coarse) are available.

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Carboguard 695 CLR

Made to Order or imported lines subject to availability.

Carboguard 695 CLR is a solventless, clear, epoxy lining that can be applied using reinforced mat specifically designed to comply with API RP652** for thick-film tank bottom lining repairs. It is suitable for exposures in water, crude oil, aromatic distillates, and unblended gasolines.

It is suitable for exposures in water, crude oil, aromatic distillates, and unblended gasolines. It can be applied by standard or plural-component airless spray equipment

 

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Carboguard 695 PM

Made to Order or imported lines subject to availability. Certified handlers only.

Carboguard 695 PM is a solventless, epoxy surfacer or patching mortar that is used to:

Fuel & Other Tanks: Transition between floor-wall chine areas, lapwelded plates, rivets, etc. It is typically used with a reinforced mat system specifically designed to comply with API RP652 for thick-film tank bottom lining repairs.

It is suitable for exposures in water, crude oil, aromatic distillates, and unblended gasolines. It is typically applied by broadknife, spatula, trowel, brush, or other suitable tool that allows heavy applications and smoothing procedures.

Excellent surfacer / patching mortar for concrete tanks & floors. Provides a rapid return to service screed for repairing flooring in high chemical exposure industrial environments.

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Carboguard 696 HBE

Made to Order or imported lines subject to availability. 

Carboguard® 696 HBE is a phenalkamine cured high solids, syntactic foam modified high build epoxy coating

Carboguard® 696 HBE is designed for single coat application as a penstock lining to film thicknesses typically ranging between 400 & 600 microns using correctly equipped industry standard airless spray equipment of sufficient capacity.

Carboguard® 696 HBE is suitable for service in immersion, on buried structures, and on high wear surfaces in atmospheric exposure

  • High Build Single Coat – 0.4mm to 0.6 mm in a single coat
  • Extensive case history in hydro penstocks and scroll casings
  • Potable water compliant formulation (refer Carboguard 696 UHBE)
  • Positive cure, even at low temperatures
  • Abrasion resistant
  • Unique flexibilised formulation imparts excellent impact resistance
  • May be used on buried structures, structures immersed in fresh or salt water, and for atmospheric exposure
  • Suitable for use with cathodic protection systems – impressed current or anode types
  • Low density of 1.09 – heavy duty protection with minimal added weight

 

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Carbomastic 615

This high performance epoxy coating exhibits outstanding moisture and surface tolerance during application, low temperature cure capability, and very fast cure response for quick return to service. This makes Carbomastic 615 eminently suitable for maintenance repaint work in marginal conditions and where surface preparation is less than ideal.

It contains an inert flake reinforcement (micaceous iron oxide) to enhance film strength and performance.

  • High solids, low VOC
  • Low temperature cure
  • Excellent wetting properties
  • Excellent surface tolerance
  • Excellent moisture tolerance (application)
  • Fast cure response

Suitable for immersion service in fresh or salt water after 60 minute cure @ 24°C

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Carbothane 133 LH

Aliphatic Acrylic-Polyester Polyurethane Satin Finish

High build, low sheen finish that has excellent resistance to corrosion, chemicals and abrasion. Suitable for application over a number of Carboline primers and intermediates, this material provides very good weathering performance in a broad range of colours

  • Outstanding performance properties in both mild and aggressive environments
  • High build; suitable for many two-coat systems
  • Approved for use in food & dairy processing plants
  • Application by spray, brush or roller
  • Indefinite recoatability
  • VOC compliant to current AIM regulations

 

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Carbothane 134 HG

High gloss polyurethane finish with exceptional weathering performance characteristics.

Used extensively in virtually every market sector, including marine exposure, Carbothane 134 HG provides a smooth, durable finish that has superior resistance to corrosion, abrasion and chemical exposure.

  • Specialised UV protection designed for Australian and New Zealand exposures
  • Highly recoatable, with minimum preparation requirements
  • The high solids (70%) formulation creates a very cost effective coating

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Carbozinc 11

Time-tested corrosion resistant primer that protects steel galvanically in the harshest environments. For over four decades, Carbozinc 11 (CZ 11) has been the industry standard for high-performance inorganic zinc protection on steel structures worldwide

 

  • CZ 11 meets Class B slip co-efficient and creep testing criteria for use on faying surfaces
  • Rapid cure. Dry to handle in 45 minutes at 16°C and 50% relative humidity.
  • Low temperature cure down to -18°C.
  • High zinc loading.
  • Meets FDA requirements in grey color.
  • Available in ASTM D520, Type II zinc version.
  • Very good resistance to salting.
  • May be applied with standard airless or conventional spray equipment.
  • Complies with the composition and performance requirements of:
    • AS/NZS 3750.15, Type 4
    • AS 4848.1:2006 Single Coat Inorganic Zinc Silicate

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Carbozinc 11 WB

Made to Order or imported lines subject to availability.

Carbozinc 11 WB is a water-based inorganic zinc rich primer that protects steel galvanically, eliminating subfilm corrosion. It meets VOC regulations while providing the proven performance of silicate zinc rich technology. It may be used as a primer under many different types of topcoats

 

  • Excellent corrosion protection
  • High zinc loading per square metre
  • Zero VOC
  • Good resistance to salting
  • Fast curing, quick handling
  • Excellent application characteristics (less likely to pump packing or tip plug)
  • Meets Class B slip coefficient* and creep testing criteria for use on faying surfaces.
  • Conforms to AS/NZS 3750.15 Type 3

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Carbozinc 858

NEW 4:1 Ratio

Low VOC organic zinc epoxy steel primer with quick cure-to-topcoat characteristics for in-shop  applications and quick turnaround requirements in the field. Carbozinc 858 has very good adhesion and undercutting resistance and is excellent for use as a corrosion resistant primer for a variety of applications

 

  • Meets SSPC Paint System 20
  • Fully complies with AS 3750.9:1994 Type 2 Organic Zinc Rich
  • Low temperature cure down to 2°C
  • Protects against undercutting corrosion
  • May be applied with standard airless or conventional spray equipment
  • VOC compliant to current AIM regulations

Availability :

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Carbozinc 859 EZ2

A very economic, two-component, high solids, zinc rich epoxy primer formulated for the protection of properly prepared steel substrates.

Carbozinc 859 EZ2 can be applied by conventional, airless, or plural component spray. Recommended where a high performance, highly corrosion resistant zinc primer is desired.

Typical applications include structural steel, tanks, piping, equipment and other miscellaneous parts in industrial, offshore or architectural projects.

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Chem~Bar 3500

Chem~Bar™3500 Primer is a single pack steel primer designed for use in industrial and marine applications.

For atmospheric exposures, Chem~Bar 3500™Primer is normally topcoated with Chem~Bar 900™Finish.

 

Chem~Bar 3500™Primer may be:

  • Applied directly over steel or over zinc primers such as Carbozinc® 859 EZ2, Carbozinc® 858, Zinkex 100 or Carbozinc® 11.
  • Used on substrates other than steel, (consult Altex Coatings for specific recommendations.)

Chem~Bar 3500™Primer is used in the commercial marine sector as a:

  • barrier/seal coat over aged or incompatible/unknown antifoulings
  • as a tie coat over suitably prepared, aged epoxy coatings prior to application of the selected Sea~Barrier® antifouling
  • sealant to assist in the prevention of TBT leaching from an underlying antifouling coating - provided it is applied at a minimum dry film thickness of 80 microns (minimum 2 coats by roller).

It is normally overcoated with Sea~Barrier® 1000, 3000 or Sea~Barrier® Alloy 100 PLUS Anti-fouling.

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Chem~Bar 900

Chem~Bar 900™ is specifically formulated to protect metal or masonry surfaces exposed to weather, water or chemicals.

Chem~Bar 900™ may be used to protect structural steel, tanks, pipes and equipment a vast range of industries.

It's recoatable properties, highly anti-corrosive formulation and ease of application make it an ideal coating for both maintenance and new work.

  • Pulp and Paper Industry
  • Chemical Process Industry
  • Sewage and Waste Water Plants
  • Water Tanks
  • Refineries
  • Fertiliser Plants
  • Marine Installations
  • Bridges
  • Power Projects
  • Containers
  • Shipping

 

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Chem~Bar 900 Aluminium MS Sealer

Metal Spray Sealer - a traditional Vinyl sealer used in accordance with ASNZ2312 Zinc Metalspray systems, as well as a single package high performance aluminium filled vinyl-acrylic finish suitable for use as a general purpose aluminium finish.

Chem~Bar 900™ Aluminium may be used in all atmospheric exposures where traditional aluminium finishes may be employed; including:

  • Pulp and Paper Industry
  • Chemical Process Industry
  • Sewage and Waste Water Plants
  • Water Tank & Silo Exteriors
  • Refineries
  • Fertiliser Plants
  • Marine Installations
  • Bridges
  • Power Projects
  • Containers
  • Shipping

 

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

E~Line 379

E~Line 379® is a high gloss, high performance, two component, chemically cured polyaspartic urethane designed for use in areas where maximum gloss and colour retention are required.

E~Line 379® will provide excellent gloss and colour retention as well as resistance to moderate to severe corrosive environments for:

  • Transportation industry
  • Chemical processing industry
  • Pulp and paper industry
  • Dairy industry
  • Bridges and storage tanks
  • Light colours and clear may be used as anti-graffiti coatings due to their excellent solvent resistance - refer also to Altex Graffiti Remover and Easy~Clean SX Additive
  • Outstanding abrasion resistance
  • Excellent durability due to high flexibility and toughness
  • Exceptional tolerance to marginal application conditions
  • Exceptional retention of cosmetic properties due to high UV resistance

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Filler #50

Graded silica blend for epoxy putty / mortar mixes

Availability :

View More NZ Safety Data Sheet Aus. Safety Data Sheet

Glass Flake Additive

Reinforcing additive for a range of Carboguard epoxy coatings

Availability :

View More NZ Safety Data Sheet Aus. Safety Data Sheet

Intumastic 285

Made to Order or imported lines subject to availability. 

Single package, water-based, flexible mastic fire protective coating for cables and cable trays.

A water based mastic that can be applied to electrical cables to retard fire propagation. Once applied, it meets code and insurance requirements for interior and exterior use. It provides a hard and flexible surface that will not dust, flake, or spall

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Phenoline 1205

Made to Order or imported lines subject to availability. 

A glass flake-filled coating with dense cross-linking that exhibits excellent overall chemical resistance to a variety of aggressive chemicals. Glass reinforcement provides added abrasion resistance, permeation resistance and internal reinforcement.

Phenoline® 1205 exhibits very good acid resistance. Excellent for lining tanks or pipes in process facilities where hot water or abrasive conditions exist. Also used as a primary or secondary containment lining for a variety of aggressive chemicals

  • Excellent resistance to acids, caustics, ethanol, gasoline, jet fuels and solvents
  • Excellent abrasion resistance
  • Excellent thermal shock resistance
  • Excellent resistance to deionized or demineralised water up to 82°C
  • Excellent resistance to crude oil, brine or water up to 93°C

 

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Phenoline 311

Made to Order or imported lines subject to availability.

Phenoline 311 is a holding primer designed for application in storage / tanks prior to application of the selected tank coating.

Featuring Low Temperature Cure, Potable Water approval (AS4020 / ANSI/NSF ) and extended recoat times this Novalac / Phenalkamine primer provides exceptional corrosion resistance and adhesion properties.

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Phenoline 353 LTE

Made to Order or imported lines subject to availability. 

High solids modified novalac epoxy, with excellent low temperature cure and outstanding chemical resistance.

Provides immersion grade service for a vast range of chemicals (refer Data Sheet)  in a wide range of industries:

 

Wastewater

Petrochemical

Industrial manufacturing / processing

Chemical transport

 

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Phenoline Tank Shield

 

Made to Order or imported lines subject to availability. 

Amine Adduct cured epoxy. This product is a solvent-free, high performance epoxy coating designed as an internal tank, valve and pipe lining for chemical or other commodity storage.

The product is blush resistant and is typically applied at film thicknesses of 500-625 microns or thicker as needed (tank floors). It will withstand exposures typically seen in the oil and gas industries; crude oils and fuels. It is resistant to NGL condensates, produced water, brines, and industrial process water.

Availability :

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Phenoline Tank Shield FP

This product is a solvent-free, high performance epoxy coating specifically designed as a pit
filling primer with ideal flow properties allowing it to wet-out and fill moderate to severe pitting on
steel tank bottoms. It's unique formula allows simple batch mixing for ease of application. With an
appropriate lining, it can handle exposures typically seen in the oil and gas industries. It is resistant
to crude oil, NGL condensates, produced water, brines, and industrial process water.

Availability :

View More Product Data Sheet NZ Safety Data Sheet 

Pyrocrete 241 (see Notes)

Made to order or imported product subject to avalability.

Cementitious inorganic fireproofing formulation

Recommended uses for the fire protection of structural steel, bulkheads, and upgrading the fire resistance of existing concrete. Recommended areas of application are refineries, petrochemical, pharmaceutical facilities, pulp and paper mills, offshore platforms, nuclear and conventional power plants, factories, warehouses, institutional and biomedical facilities.

  • Easily applied by spray or trowel
  • Lightweight – one-third the weight of concrete for equal fire protection
  • Excellent physical properties – hard, durable, Non-friable – high impact strength
  • Nonflammable – during or after application
  • Asbestos-free – complies with all US EPA and OSHA regulations
  • Chloride and sulphide free – no special priming required
  • Single package – mixed with clean, potable water at the job site
  • Tested & approved for exterior use by Underwriters Laboratories, Inc
  • Quality Manufactured – strict Carboline quality standards monitored by UL

Unique crack-free formulation

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Reactamine 760 HB

Made to Order or imported lines subject to availability.

Environmentally friendly, advanced hybrid technology, plural-component applied coating used as a lining for water, wastewater, manholes, penstocks, dam gates, pipelines and other aggressive immersion applications. Provides protection against microbiologically induced corrosion (MIC) and hydrogen sulfide corrosion found in wastewater treatment service. Ultra high build product designed to be applied at high thickness in one coat application. 

Availability :

View More Product Data Sheet NZ Safety Data Sheet 

Rustbond

Rustbond is a cross-linked penetrating primer/sealer with excellent wetting properties. It is highly flexible with good chemical and solvent resistance, and will accept a variety of topcoats.

Recommended use as primer/sealer for marginally prepared steel and over old coatings. The excellent wetting properties allows it to penetrate rust and discontinuities in existing coatings and provide a firm anchorage for a variety of topcoats.

The thixotropic character reduces run off, ensuring that the edges of existing coatings are encapsulated thus reducing undercutting and peeling.

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Thermaline 400 Primer & Finish

Made to order or imported product subject to avalability.

A high performance, immersion grade coating system which has excellent resistance to wet/dry cycling conditions at elevated temperatures

  • Temperature resistance to 204°C (400°F)
  • Very good flexibility
  • Excellent overall chemical resistance
  • Very good abrasion resistance
  • Easily applied by spray
  • Acceptable for use over stainless steels

Used in conjunction with Thermaline 400 Primer

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Thermaline 4900

Air-dried silicone acrylic coating available in Aluminium and suitable for high temperature exposures up to 232°C. Air-drying characteristics allow for faster handling of in-shop applications than with other high-temperature coatings.

Heat cure above 149°C is recommended and will impart added strength and integrity to the coating.

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Thermaline Heat Shield

Made to order or imported product subject to avalability.

This is an extreme performance coating for hot, cryogenic and cycling exposures. Thermaline Heat Shield contains a unique blend of plate-like reinforcing pigments fortified with an inert polymeric matrix. The resulting film provides an outstanding barrier against corrosives and harsh exposures typically seen in elevated temperature environments. This versatile coating is ideal for all piping, vessels and equipment operating from cryogenic conditions up to 1200°F. It is particularly well suited to prevent corrosion under insulated equipment/piping for both carbon steel substrates and stainless steels. This fortified coating has superior shop handling properties over standard silicone coatings (see Curing). It is recommended for CS-6 and SS-5 systems of NACE SP0198 Standard Practice for coatings to control corrosion under insulation (CUI).

Availability :

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Thermo-Lag 3000-SP

Made to order or imported product subject to avalability.

A two component, epoxy based, thermally activated, intumescent coating for the fire protection of structural steel.

Thermo-Lag® 3000 SP is designed to fireproof steelwork for up to a 4 hour fire rating, depending on the design. The recommended use for this product is fireproofing of steel beams, columns, tubes, pipes, vessel skirts, bulkheads, underdecks and electrical raceways

 

  • UL listed – designs for many types of steel sections up to 4 hours fire rating for both interior and exterior environments.
  • Lloyds Register & DNV certified up to 3 hours protection, interior & exterior
  • Durable finish – provides a hard, durable finish resistant to normal wear & tear.
  • Thin film coating – offers an economical solution to alternative fireproofing.
  • VOC compliant.
  • Jet-Fire rated when used in conjunction with Thermo-Lag® 3002.

 

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Offline

* Sorry, we aren’t online at the moment. Please fill out the form below and we will get back to you as soon as possible.