logo

Water and Wastewater

Carbocrete 522

Made to Order or imported lines subject to availability.

Fibre Reinforced Cementitious Mortar

A spray-grade, economical, shrinkage-compensated, repair mortar, and surfacing compound that exhibits excellent bond strength to concrete. It is ideally suited for substrate resurfacing of deteriorated concrete and is typically topcoated with Carboline’s lining systems. Various lining systems are available. Each system provides excellent corrosion protection against targeted exposures, especially to acid attack due to wet hydrogen sulfide environment found in wastewater

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Carboguard 504

Carboguard® 504 is an inert non-inhibitive anti-corrosive modified polyamide cured epoxy primer.

  • Excellent primer for water and many aqueous chemicals immersion service when top-coated with an approved finish
  • Excellent adhesion to difficult substrates
  • Excellent holding primer
  • Excellent corrosion resistance
  • Complies with AS/NZS 3750.13 (2 pack epoxy primer), Types 1, 2 & 3.
  • Good abrasion resistance
  • Very good aged re-coatability
  • Resists splash and spillage or fumes of a wide range of chemicals
  • Easy application by brush, roller or spray
  • Ideal tie-coat over inorganic zincs
  • Versatile - can be used on most substrates under many different types of topcoat
  • Long pot-life
  • Excellent maintenance touch-up primer for hand-cleaned substrates

A user-friendly primer for epoxy or polyurethane systems in environments not suited to zinc primers due to acidic or alkaline fallout or splash & spill.

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Carboguard 510 SG

Made to Order or imported lines subject to availability.

A spray-grade, economical, epoxy-based repair mortar, patching and surfacing compound that exhibits excellent bond strength to concrete and other masonry surfaces. It is ideally suited for resurfacing deteriorated concrete in wastewater environment. Topcoated with Carboline’s lining systems provides protection from acid attack from H2S or MIC. Unique spraygrade (SG) formulation speeds application properties for quick turnaround projects

  • Epoxy modification improves chemical resistance for wastewater environment
  • Zero VOC
  • Water based, low odour
  • Excellent film strength, abrasion, and impact resistance
  • Easily topcoated to provide additional chemical resistance or appearance
  • Self-priming over concrete
  • Aggregate reinforced

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Carboguard 635 HAR

A rapid cure to topcoat epoxy with high abrasion resistance along with other valuable attributes including:

  • low-temperature cure
  • surface tolerance
  • fast recoat times
  • moisture tolerance during application and cure
  • excellent corrosion protection.

Carboguard 635 HAR can be used direct to metal as a corrosion resistant primer or as an intermediate coating over other primers. It may also be used for immersion in fresh or salt water exposures, and exhibits exceptional abrasion resistance and toughness.

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Carboguard 636

A highly versatile multi-purpose Phenalkamine Epoxy High Build coating.

Carboguard® 636 is an advanced technology coating suited to marine and industrial applications and suitable for atmospheric and many immersion exposures. The DTM properties make Carboguard® 636 a versatile coating in maintenance and new work applications. Syntactic foam modification gives Carboguard® 636 unique thermal shock resistance and flexibility

  • Marine systems - below the waterline, and fresh water systems
  • AS4020 Potable Water Approval for Haze Grey & Grey/White colours only.
  • Vast range of industrial environments
  • Very good flexibility – resists chipping and aged embrittlement
  • Lighter weight – 13% lighter than most similar coatings
  • Versatile, surface tolerant coating suitable for water jet cleaned surfaces
  • Tolerant to surface dampness - particularly when brush applied
  • Good thermal qualities; excellent for use under insulation to 120ºC
  • Good adhesion to tight rust - especially when used in conjunction with Rustbond® or Altra~Lock 576
  • Self-priming (DTM) for many applications
  • Fast dry to recoat and excellent dry to handling
  • Low temperature cure to below freezing; -5°C

 

Availability :- New Zealand

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Carboguard 640

Made to Order or imported lines subject to availability.

Carboguard® 640 is a high performance, two-component, modified phenalkamine, chemically cured, immersion grade epoxy barrier coating

Carboguard® 640 is an ideal high build coating for any service or structure, marine or industrial, where water or corrosion resistance is required.

Carboguard® 640 has excellent proven long-term service case histories for marine hull externals, above & below water, and as a lining for hydro penstocks and gates and similar permanently immersed structures.

Carboguard® 640 is the barrier coating of choice under Altex Sea~Barrier™ 1000, 3000 and Alloy 100Plus antifoulings

 

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Carboguard 690

High performance, surface tolerant epoxy that has excellent resistance to water and wastewater exposures. This coating exhibits outstanding moisture tolerance during application, low temperature cure capability, and very fast cure response for quick return to service.

  • Fully tintable epoxy high build
  • Suitable for all industrial and marine environments.
  • Carboguard 690 is also certified for use in both food processing and potable water storage and reticulation

Food Processing

NZ AsureQuality assessed & passed for food/beverage including dairy farm & factory non-incidental contact. Ref: H3108

 

Potable Water Approval – AS 4020:2005

Australian Water Quality Centre

Carboguard 690 White*        Reference: 130243-2009-CSR-1

Carboguard 690 N53 Bl/Gr*  Reference: 130243-2009-CSR-2

AMS Laboratories

Carboguard 690 N35 Lt. Gr* Reference: AMS 1316537A

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Carboguard 690 GF

Phenalkamine Epoxy with Glass Flake Additive to increase chemical, abrasion & thermal shock resistance

High performance, surface tolerant epoxy that has excellent resistance to water and wastewater exposures. This coating exhibits outstanding moisture tolerance during application, low temperature cure capability, and very fast cure response for quick return to service. Can be used on structural steel, piping, tankage, and equipment exposed to industrial or marine environments.

It can also be used in immersion service for salt water, process water (non-potable) and waste water treatment projects

  • Glass Flake Reinforced
  • Increased chemical, abrasion & thermal shock resistance
  • Suitable for service under insulation (CUI) up to 150°C – 1 coat at 150 microns DFT
  • High solids, low VOC
  • High build (200 microns)
  • Low temperature cure -7°C (20°F), Fast cure response

Available in a range of standard and tintable colours.

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Carboguard 695 PM

Made to Order or imported lines subject to availability. Certified handlers only.

Carboguard 695 PM is a solventless, epoxy surfacer or patching mortar that is used to:

Fuel & Other Tanks: Transition between floor-wall chine areas, lapwelded plates, rivets, etc. It is typically used with a reinforced mat system specifically designed to comply with API RP652 for thick-film tank bottom lining repairs.

It is suitable for exposures in water, crude oil, aromatic distillates, and unblended gasolines. It is typically applied by broadknife, spatula, trowel, brush, or other suitable tool that allows heavy applications and smoothing procedures.

Excellent surfacer / patching mortar for concrete tanks & floors. Provides a rapid return to service screed for repairing flooring in high chemical exposure industrial environments.

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Carboguard 696 HBE

Made to Order or imported lines subject to availability. 

Carboguard® 696 HBE is a phenalkamine cured high solids, syntactic foam modified high build epoxy coating

Carboguard® 696 HBE is designed for single coat application as a penstock lining to film thicknesses typically ranging between 400 & 600 microns using correctly equipped industry standard airless spray equipment of sufficient capacity.

Carboguard® 696 HBE is suitable for service in immersion, on buried structures, and on high wear surfaces in atmospheric exposure

  • High Build Single Coat – 0.4mm to 0.6 mm in a single coat
  • Extensive case history in hydro penstocks and scroll casings
  • Potable water compliant formulation (refer Carboguard 696 UHBE)
  • Positive cure, even at low temperatures
  • Abrasion resistant
  • Unique flexibilised formulation imparts excellent impact resistance
  • May be used on buried structures, structures immersed in fresh or salt water, and for atmospheric exposure
  • Suitable for use with cathodic protection systems – impressed current or anode types
  • Low density of 1.09 – heavy duty protection with minimal added weight

 

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Carbomastic 615

This high performance epoxy coating exhibits outstanding moisture and surface tolerance during application, low temperature cure capability, and very fast cure response for quick return to service. This makes Carbomastic 615 eminently suitable for maintenance repaint work in marginal conditions and where surface preparation is less than ideal.

It contains an inert flake reinforcement (micaceous iron oxide) to enhance film strength and performance.

  • High solids, low VOC
  • Low temperature cure
  • Excellent wetting properties
  • Excellent surface tolerance
  • Excellent moisture tolerance (application)
  • Fast cure response

Suitable for immersion service in fresh or salt water after 60 minute cure @ 24°C

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Carboquick 200

This fast cure high build polyaspartic coating provides excellent corrosion protection as well as long term weatherability in just one coat.

It can be applied direct to metal (DTM) at 150 to 250 µms dry film thickness (DFT) to eliminate the need for typical primers and/or intermediate coats. This significantly speeds up the painting process, saves labor, and saves money without sacrificing performance. If even better corrosion protection is desired it can be applied over our time proven Carbozinc or Carboguard primers.

Availability :

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Chem~Bar 900

Chem~Bar 900™ is specifically formulated to protect metal or masonry surfaces exposed to weather, water or chemicals.

Chem~Bar 900™ may be used to protect structural steel, tanks, pipes and equipment a vast range of industries.

It's recoatable properties, highly anti-corrosive formulation and ease of application make it an ideal coating for both maintenance and new work.

  • Pulp and Paper Industry
  • Chemical Process Industry
  • Sewage and Waste Water Plants
  • Water Tanks
  • Refineries
  • Fertiliser Plants
  • Marine Installations
  • Bridges
  • Power Projects
  • Containers
  • Shipping

 

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

E~Line 379

E~Line 379® is a high gloss, high performance, two component, chemically cured polyaspartic urethane designed for use in areas where maximum gloss and colour retention are required.

E~Line 379® will provide excellent gloss and colour retention as well as resistance to moderate to severe corrosive environments for:

  • Transportation industry
  • Chemical processing industry
  • Pulp and paper industry
  • Dairy industry
  • Bridges and storage tanks
  • Light colours and clear may be used as anti-graffiti coatings due to their excellent solvent resistance - refer also to Altex Graffiti Remover and Easy~Clean SX Additive
  • Outstanding abrasion resistance
  • Excellent durability due to high flexibility and toughness
  • Exceptional tolerance to marginal application conditions
  • Exceptional retention of cosmetic properties due to high UV resistance

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Glass Flake Additive

Reinforcing additive for a range of Carboguard epoxy coatings

Availability :

View More NZ Safety Data Sheet Aus. Safety Data Sheet

Phenoline 353 LTE

Made to Order or imported lines subject to availability. 

High solids modified novalac epoxy, with excellent low temperature cure and outstanding chemical resistance.

Provides immersion grade service for a vast range of chemicals (refer Data Sheet)  in a wide range of industries:

 

Wastewater

Petrochemical

Industrial manufacturing / processing

Chemical transport

 

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Phenoline Tank Shield FP

This product is a solvent-free, high performance epoxy coating specifically designed as a pit
filling primer with ideal flow properties allowing it to wet-out and fill moderate to severe pitting on
steel tank bottoms. It's unique formula allows simple batch mixing for ease of application. With an
appropriate lining, it can handle exposures typically seen in the oil and gas industries. It is resistant
to crude oil, NGL condensates, produced water, brines, and industrial process water.

Availability :

View More Product Data Sheet NZ Safety Data Sheet 

Reactamine 760 HB

Made to Order or imported lines subject to availability.

Environmentally friendly, advanced hybrid technology, plural-component applied coating used as a lining for water, wastewater, manholes, penstocks, dam gates, pipelines and other aggressive immersion applications. Provides protection against microbiologically induced corrosion (MIC) and hydrogen sulfide corrosion found in wastewater treatment service. Ultra high build product designed to be applied at high thickness in one coat application. 

Availability :

View More Product Data Sheet NZ Safety Data Sheet 

Reactamine Joint Seal

Made to Order or imported lines subject to availability. 

Reactamine Joint Seal FC is a 2-component 100% solids, polyurea-based joint sealant that is self-leveling and cures in approximately 30 minutes. It works equally well with asphalt and concrete and protects interior horizontal concrete expansion and control joints from spalling, chipping and breakdown. This product can be applied at temperatures ranging from -18° to 65°C and possesses excellent chemical resistance, water resistance and thermal stability at both high and low temperatures

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Rustbond

Rustbond is a cross-linked penetrating primer/sealer with excellent wetting properties. It is highly flexible with good chemical and solvent resistance, and will accept a variety of topcoats.

Recommended use as primer/sealer for marginally prepared steel and over old coatings. The excellent wetting properties allows it to penetrate rust and discontinuities in existing coatings and provide a firm anchorage for a variety of topcoats.

The thixotropic character reduces run off, ensuring that the edges of existing coatings are encapsulated thus reducing undercutting and peeling.

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Thermaline 400 Primer & Finish

Made to order or imported product subject to avalability.

A high performance, immersion grade coating system which has excellent resistance to wet/dry cycling conditions at elevated temperatures

  • Temperature resistance to 204°C (400°F)
  • Very good flexibility
  • Excellent overall chemical resistance
  • Very good abrasion resistance
  • Easily applied by spray
  • Acceptable for use over stainless steels

Used in conjunction with Thermaline 400 Primer

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Offline

* Sorry, we aren’t online at the moment. Please fill out the form below and we will get back to you as soon as possible.