A solvent-free, epoxy resin specifically formulated for use as a primer on porous concrete. Can be used as for coving and patching when used in conjunction with select Altex Ancillary products – Contact Technical Services for further information.
A three component, solvent free high strength multi-purpose epoxy mortar.
Commonly used as a subfloor for resinous toppings where a high strength thin section screed is required. Can be laid to falls and feathered down to a minimum thickness of 1mm, maximum thickness of 50mm (in one application)
A high-performance, multi-purpose flooring epoxy coating that is easy to apply. It’s ideal for use in many flooring environments such as workshops, warehouses, factories, washrooms etc.
Available in a variety of standard colours.
• Self-priming on suitably prepared concrete, or over suitably primed surfaces
• Low odour
• Low viscosity
• Low VOC / High solids
• Can be top coated with Carbothane 133 LH or E~Line series - Refer to Technical Services for further advice
• Resistant to hydraulic fluids and Skydrol once fully cured
• Tested to AS 4586:2013, Slip resistance classification of new pedestrian surface materials - Refer Certification section for more information.
A solvent-free, epoxy resin specifically formulated for use as a primer on porous concrete under Altra~Floor EF. Can be used as for coving when used in conjunction with select Altex Ancillary products – Contact Technical Services for further information.
Flowcoat OP is a hardwearing and solvent free, epoxy resin flooring solution used to service various manufacturing workspaces by delivering the level best in protective and chemical resistant floor coatings.
The low maintenance, seamless and hygienic finish is aesthetically attractive. Designed to create a uniform "Orange Peel" surface texture, Flowcoat OP may be used as a hard wearing protective floor coating.
Flowfast Binder is a medium viscosity, colourless, 2 component reactive methyl methacrylate (MMA) resin.
Typically used as a Binder within the Flowfast flooring range. Systems using Flowfast Binder as the main binder must always be treated with a Flowfast Sealer (e.g. Flowfast Sealer or Flowfast Flexible Sealer). Flowfast Binder is a general purpose resin; it must not be used in areas subject to heavy hot water loading.
Flowfast Flexible Binder is a 2 component reactive flexible methyl methacrylate (MMA) modified resin.
Flowfast Flexible Binder is typically used in the following applications.
• To provide a wearing and protect coats to Flowcrete MMA Waterproof membranes.
• Flexible floor coverings especially if exposed to low temperatures e.g. coolers and freezers.
• As a wearing layer for outdoor applications exposed to heavy mechanical loadings and rapid temperature variations i.e. ramps, bridges and carparks.
• As an intermediate coat for floors exposed to hot water.
Flowfast Flexible Sealer is a medium viscosity, UV-resistant, 2 component reactive methyl methacrylate resin (MMA).
Flowfast Flexible Sealer is used as part of the Deckshield Rapide and Flowfast range. In the liquid state it is blue-violet in colour. After polymerisation the sealer dries clear. Flowfast Flexible Sealer resists occasional hot water spillage up to 80°C. The flexibility and high UV resistance are also ideal for outdoor applications.
Flowfresh Coating is a 4-component, solvent free, antimicrobial coloured polyurethane cement coating with a matte finish.
Can be used as a seal coat for Flowfresh flooring systems including coving. This will provide a hard-wearing, chemical resistant, antimicrobial coloured sealer. Additionally Flowfresh Coating can be used as an alternative to Flowfresh Primer.
Flowfresh Coating Satin is a 4-component, anti-microbial, solvent free, coloured polyurethane cement coating with a satin finish.
Can be used as a seal coat for Flowfresh flooring systems including coving. This will provide a hard-wearing, chemical resistant, antimicrobial coloured sealer in a semi-gloss/satin finish.
Flowprime ESD Conductive is a 3 component low viscosity resin based conductive primer.
To be used prior to overcoating with Flowcrete’s range of electrostatic dissipative (ESD) flooring systems. Providing electrical continuity under the ESD resin floor toppings and to earthing points.
Flowseal UV Satin (clear) is a 2 component, UV stable, abrasion resistant aliphatic polyurethane sealer in a Satin/Semi gloss finish.
Typically used as a final seal coat for Flowcrete decorative systems. This will provide a high abrasion and UV light stable satin finish. Can also be used as a seal coat applied directly onto honed and polished concrete.