logo

Altra~Lock 576

A rapid dry/quick cure 100% solids penetrating epoxy sealer designed for use where less than ideal surface preparation is attainable or where surfaces have inherent porosity or surface weakness. It has a very low viscosity which allows it to wick into and bond porous substrates and residual rust into a tough epoxy composite. It may be applied to residual rust, degraded or new concrete, fibre-reinforced cement, and timber.

FEATURES:

  • Excellent wetting properties
  • 100% solids
  • Rapid cure
  • Low temperature cure as low as 4°C
  • Ideal for marginally prepared steel
  • Easy application by brush, roller, or low atomisation spray
  • Can be used to seal asbestos
  • Suitable for below waterline applications on marine vessels when used underneath a high build epoxy barrier system
  • Approved for use in food & dairy processing plants

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Altra~Zinc 605

High performance, two component, reinforced epoxy zinc-rich primer designed for use as a cathodic primer for protecting steel exposed to a variety of environments.

FEATURES:

  • Premium performance primer for most industrial systems.
  • Resists topcoat pinholing
  • Resistant to dry spray, mudcracking and topcoat bubbling
  • Easy to mix - zinc pre-mixed into base component
  •  Easy application by brush, roller, or spray
  • Fast dry-to-recoat times
  • Good low temperature cure
  • Good solvent resistance
  • Safe - contains no lead or chromate pigments
  • Versatile - can be used as the primer under numerous coating systems including fireproofing

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Carboguard 504

A high performance, immersion grade (fresh & salt water) chemically cured epoxy primer. Suitable for use over suitably prepared mild steel, galvanised steel, other non-ferrous metals, and most GRP substrates.

FEATURES:

  • Excellent primer for water and many aqueous chemicals immersion service when topcoated with an approved finish
  • Excellent adhesion to difficult substrates
  • Excellent holding primer
  • Excellent corrosion resistance
  • Complies with AS/NZS 3750.13 (2 pack epoxy primer), Types 1, 2 & 3.
  • Approved for use in NZ Food Processing Plants
  • Good abrasion resistance
  • Very good aged re-coatability
  • Resists splash and spillage or fumes of a wide range of chemicals
  • Easy application by brush, roller or spray
  • Ideal tie-coat over inorganic zincs
  • Versatile - can be used on most substrates under many different types of topcoat
  • Long pot-life
  • Excellent maintenance touch-up primer for hand-cleaned substrates
  • A user-friendly primer for epoxy or polyurethane systems in environments not suited to zinc primers due to acidic or alkaline fallout or splash & spill
  • Excellent tie-coat over high build epoxies as an extended 2-3 day recoat window with Sea~Barrier Antifoul series – Carboguard 504 Grey is preferred. Refer to Technical Services for further advice

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Carboguard 504 ZP

Availability: Australia only

A high performance, immersion grade (fresh & salt water) chemically cured, zinc phosphate epoxy primer. Suitable for use over suitably prepared mild steel, galvanised steel, other non-ferrous metals, and most GRP substrates.

FEATURES:

  • Excellent adhesion to difficult substrates
  • Excellent holding primer
  • Excellent corrosion resistance
  • Complies with AS/NZS 3750.13 (2 pack epoxy primer), Types 1, 2 & 3.
  • Good abrasion resistance
  • Very good aged re-coatability
  • Resists splash and spillage or fumes of a wide range of chemicals
  • Easy application by brush, roller or spray
  • Versatile - can be used on most substrates under many different types of topcoat
  • Long pot-life
  • Excellent maintenance touch-up primer for hand-cleaned substrates
  • A user-friendly primer for epoxy or polyurethane systems in environments not suited to zinc primers due to acidic or alkaline fallout or splash & spill
  • Excellent tie-coat over high build epoxies as an extended 2-3 day recoat window with Sea~Barrier Antifoul series. Refer to Technical Services for further advice

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Carboguard 636 PW

Made to Order.

High performance immersion grade epoxy that is designed as a liner for potable water tanks. This coating exhibits moisture tolerance during application, low temperature cure capability, and fast cure response for quick return to service. Product is self-priming on steel and is normally applied in two coats. Formulated for application at 120 to 180 microns DFT per coat for potable use.

FEATURES:

  • Very good flexibility – resists chipping and aged embrittlement
  • Lighter weight – 13% lighter than most similar coatings
  • Versatile surface tolerant coating
  • AS/NZS 4020 Potable Water Approval
  • Lower viscosity allows application at higher solids (less thinning) and reduced VOC at application
  • Fast dry to recoat
  • Low temperature cure to below freezing; -5°C
  • Reduced HAPS and Low VOC

 

Availability :- New Zealand

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Carboguard 636 XT

A multi-purpose, advanced technology coating suited to marine and industrial applications. Suitable for atmospheric and many immersion exposures. The DTM properties make it a versatile coating in maintenance and new work applications. Syntactic foam modification gives it unique thermal shock resistance and flexibility.

Link

 

Availability :

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Carboguard 636 XT GF

A glass-flake filled, multi-purpose,advanced technology coating suited to marine and industrial applications. Suitable for atmospheric and many immersion exposures. The DTM properties make it a versatile coating in maintenance and new work applications. Syntactic foam modification gives it unique thermal shock resistance and flexibility. Glass flake reinforcement enhances film strength, impact resistance and barrier properties.

FEATURES:

  • Excellent physical and barrier properties
  • Versatile surface tolerant coating
  • Good adhesion to tight rust - especially when used in conjunction with Rustbond PS or Altra~Lock 576
  • Tolerant to surface dampness - particularly when brush/roller applied
  • Fast dry to recoat
  • Excellent dry to handling properties
  • Suitable for fresh and salt water immersion
  • Low temperature cure to below freezing; down to -5°C
  • Reduced HAPS and low VOC
  • Cleaner colours and improved colour stability

Availability :

View More Product Data Sheet 

Carboquick 200

This fast cure high build polyaspartic coating provides excellent corrosion protection as well as long term weatherability in just one coat.

It can be applied direct to metal (DTM) at 150 to 250 µms dry film thickness (DFT) to eliminate the need for typical primers and/or intermediate coats. This significantly speeds up the painting process, saves labor, and saves money without sacrificing performance. If even better corrosion protection is desired it can be applied over our time proven Carbozinc or Carboguard primers.

Availability :

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Carbothane 134 HG

High gloss polyurethane finish with exceptional weathering performance characteristics.

Used extensively in virtually every market sector, including marine exposure, Carbothane 134 HG provides a smooth, durable finish that has superior resistance to corrosion, abrasion and chemical exposure.

  • Specialised UV protection designed for Australian and New Zealand exposures
  • Highly recoatable, with minimum preparation requirements
  • The high solids (70%) formulation creates a very cost effective coating

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Carboweld 11

Made to Order or imported lines subject to availability.

Self curing, zinc filled inorganic weldable holding primer.

A weldable inorganic zinc primer, which is both self curing and weldable. Welds made over Carboweld 11 coated steel are equal in every respect to welds joining uncoated steel prior to fabrication.

Weld spatter does not adhere to or damage the coating. Coated steel can be welded as quickly and easily as bare steel without loss in strength or consistency of the weld.

May be top coated with Carbozinc 11 and most conventional paints and coatings.

Carboweld 11 is used as a preconstruction primer in shipyards and fabricating shops. It has many cost saving advantages over conventional shop primers

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Carbozinc 11

Time-tested corrosion resistant primer that protects steel galvanically in the harshest environments. For over four decades, Carbozinc 11 (CZ 11) has been the industry standard for high-performance inorganic zinc protection on steel structures worldwide

 

  • CZ 11 meets Class B slip co-efficient and creep testing criteria for use on faying surfaces
  • Rapid cure. Dry to handle in 45 minutes at 16°C and 50% relative humidity.
  • Low temperature cure down to -18°C.
  • High zinc loading.
  • Meets FDA requirements in grey color.
  • Available in ASTM D520, Type II zinc version.
  • Very good resistance to salting.
  • May be applied with standard airless or conventional spray equipment.
  • Complies with the composition and performance requirements of:
    • AS/NZS 3750.15, Type 4
    • AS 4848.1:2006 Single Coat Inorganic Zinc Silicate

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Carbozinc 11 WB

Made to Order or imported lines subject to availability.

Carbozinc 11 WB is a water-based inorganic zinc rich primer that protects steel galvanically, eliminating subfilm corrosion. It meets VOC regulations while providing the proven performance of silicate zinc rich technology. It may be used as a primer under many different types of topcoats

 

  • Excellent corrosion protection
  • High zinc loading per square metre
  • Zero VOC
  • Good resistance to salting
  • Fast curing, quick handling
  • Excellent application characteristics (less likely to pump packing or tip plug)
  • Meets Class B slip coefficient* and creep testing criteria for use on faying surfaces.
  • Conforms to AS/NZS 3750.15 Type 3

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Carbozinc 858

NEW 4:1 Ratio

Low VOC organic zinc epoxy steel primer with quick cure-to-topcoat characteristics for in-shop  applications and quick turnaround requirements in the field. Carbozinc 858 has very good adhesion and undercutting resistance and is excellent for use as a corrosion resistant primer for a variety of applications

 

  • Meets SSPC Paint System 20
  • Fully complies with AS 3750.9:1994 Type 2 Organic Zinc Rich
  • Low temperature cure down to 2°C
  • Protects against undercutting corrosion
  • May be applied with standard airless or conventional spray equipment
  • VOC compliant to current AIM regulations

Availability :

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Carbozinc 859 EZ2

A very economic, two-component, high solids, zinc rich epoxy primer formulated for the protection of properly prepared steel substrates.

Carbozinc 859 EZ2 can be applied by conventional, airless, or plural component spray. Recommended where a high performance, highly corrosion resistant zinc primer is desired.

Typical applications include structural steel, tanks, piping, equipment and other miscellaneous parts in industrial, offshore or architectural projects.

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Chem~Bar 900

Chem~Bar 900™ is specifically formulated to protect metal or masonry surfaces exposed to weather, water or chemicals.

Chem~Bar 900™ may be used to protect structural steel, tanks, pipes and equipment a vast range of industries.

It's recoatable properties, highly anti-corrosive formulation and ease of application make it an ideal coating for both maintenance and new work.

  • Pulp and Paper Industry
  • Chemical Process Industry
  • Sewage and Waste Water Plants
  • Water Tanks
  • Refineries
  • Fertiliser Plants
  • Marine Installations
  • Bridges
  • Power Projects
  • Containers
  • Shipping

 

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Chem~Bar 900 Aluminium

Metal Spray Sealer - a traditional Vinyl sealer used in accordance with ASNZ2312 Zinc Metalspray systems, as well as a single package high performance aluminium filled vinyl-acrylic finish suitable for use as a general purpose aluminium finish.

Chem~Bar 900™ Aluminium may be used in all atmospheric exposures where traditional aluminium finishes may be employed; including:

  • Pulp and Paper Industry
  • Chemical Process Industry
  • Sewage and Waste Water Plants
  • Water Tank & Silo Exteriors
  • Refineries
  • Fertiliser Plants
  • Marine Installations
  • Bridges
  • Power Projects
  • Containers
  • Shipping

 

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

E~Line 379

High gloss, high performance, two component, chemically cured polyaspartic urethane designed for use in areas where maximum gloss and colour retention are required.

FEATURES:

  • Polyaspartic acrylic technology provides exceptional gloss and colour retention
  • Outstanding cosmetic properties
  • Outstanding abrasion resistance
  • Excellent durability due to high flexibility and toughness
  • Exceptional retention of cosmetic properties due to high UV resistance
  • Outstanding chemical resistance
  • Light colours along with a finish coat of Carbothane 130 Clear Coat may be used as an anti-graffiti system due to the excellent solvent resistance - refer also to and Easy~Clean SX Additive
  • High volume solids - Low VOC
  • Available with Ultra-Fresh Antimicrobial Additive where hygienic germ-free coating systems are required.
  • Tested and in compliance to Main Roads WA - Specification 908 and NZTA (Waka Kotahi) - Specification S10 for Anti-Graffiti Coatings
  • Approved for use in food & dairy processing plants

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

E~Line 949

E~Line 949 is a fast cure, economical, high gloss, aliphatic polyurethane designed for use in areas where good gloss and colour retention are required.

E~Line 949 is ideal for use where a polyurethane finish is specified and where economy and rapid drying are desirable. It will provide good gloss and colour retention as well as resistance to moderate to severe corrosive environments for:

  • Structural Steel
  • Shop application
  • Chemical processing industry
  • Pulp and paper industry
  • Dairy industry
  • Bridges and storage tanks

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Road Marking Paint

Designed for road surfaces with a relatively high vehicle traffic count, providing a higher level of durability than traditional road marking paints.

Availability :

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Rustbond PS

Rustbond PS is a very low VOC epoxy primer/sealer that combines outstanding surface tolerance characteristics over marginally prepared substrates and user-friendly features. It accepts a variety of topcoats and can help save time and money by minimising surface preparation requirements for new construction, maintenance and overcoating projects. Rustbond PS has good pot life at higher
temperatures to help minimise waste and also cures at low temperatures down to 1.7°C with Epoxy Accelerator so you have one Rustbond product for year-round application.

Availability :

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Zinkex 100

Zinkex 100 is an excellent primer for chlorinated rubber and vinyl finish coats. It may be used as a “cold galvanising” coating for the repair of hot-dip galvanised surfaces.

Zinkex 100 may be left untopcoated in non-corrosive atmospheres.

Zinkex 100 is suitable for maintenance use in the following areas:

  • Chemical Industry
  • Food Industry
  • Dairy Industry
  • Steel Bridges
  • Transmission Towers

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Offline

* Sorry, we aren’t online at the moment. Please fill out the form below and we will get back to you as soon as possible.