Designed to be used in Altex Yacht & Boat Regatta® Gloss Enamel to convert the film into a cross linked (2K) acrylic.
Altex Regatta® 2K Additive may also be used in AY&B Timbercote Varnish where multiple coats are required, to reduce time between coats.

This additive will improve flow, speed up dry time, increase gloss levels and make the film harder.

C50 Surface Cleaner is a specialised solvent borne cleaner designed for the following uses:

• To wipe down freshly applied coatings prior to sanding, and prior to re-coating and/or topcoating.
• Designed to aid removal of mild finger print oils, wind blown salts & residual sanding dust.
• To remove unseen moisture residues.

​

D30 Degreaser/Dewaxer is designed to remove more persistent surface contamination-oils and grease in industrial environments, marine situations, as well as wax from finish coats on pleasure craft topcoat surfaces.

• Will remove most common oil/grease contaminants from most surfaces-prior to sanding/sandblasting
• Dissolves waxes and other surface polishes
• Excellent for removing Dichromate Passivation treatment from galvanised surfaces
• Excellent for wiping aluminium fabrications to remove residual oils prior to abrading.

D30 Degreaser/Dewaxer is a more aggressive cleaner than the C50 Surface Cleaner.

Easy~Clean SX Additive is a proprietary modified inorganic additive used to improve the cleaning & washing characteristics in the Altex range of polyurethane finish coats.

It also improves aqueous chemical resistance, and anti-mar properties.

This additive accelerates the cure of  Isotal Enamel.

It will increase the speed of cure, increase hardness and improve the overall finish over that of a single pack product,

Epoxy Accelerator is designed to reduce cure times in various epoxy coatings at lower temperatures. By the addition of recommended rates, cure times may be reduced by up to 50%.

Cure may also be improved by ensuring the paints are stored in warmer, ambient conditions before mixing (15-25°C), and by ensuring a full induction time is utilised. (resting the mixed paint for 15-30 minutes before use).

Flattening Paste is used for gloss reduction in coatings utilised in Industrial Facilities, for Architectural finishes, on Ocean going vessels and on Pleasure Craft.
Flattening Paste can be used:
 to create a pleasing semi-gloss finish which can reduce visual impact of surface irregularities
 to reduce glare off cabin tops, decks, painted structures etc
 to allow easy colour cross match between exterior gloss finish and interior soft tone finishes
 in cabin interiors, floors, bathrooms, staff quarters etc to achieve an architectural finish and retain protective qualities

General purpose gun-wash and equipment cleaning solvent

Inorganic, asbestos free powder for use in high strength water resistant gluing applications
Thixotropic properties of General Purpose Thickener make it an excellent anti-sag agent in fairing and filleting mixes.
Translucent properties do not affect the colour of glue line.

Reinforcing additive for a range of Carboguard epoxy coatings

Premium ultra light weight filler for fairing, filling and filleting for use above and below the waterline.

Usually mixed with AY&B Epoxy Resin at a ratio typically around the 3 Parts Microballoons to 1 Part Epoxy Resin mix.

Three grades of Non Skid Particles are available to achieve the desired texture and  finish.  May be incorporated into a wide range of coatings, either as an intermediate coat, or as a finish coat. Either broadcast into a wet film, or mixed and roller applied. Fine grade may be spray applied. All products are sieved grades, meaning the finish is consistent and attractive, with no clumping of dust particles. 

Medium and Coarse grades are highly abrasion resistant, with over 20 years of proven service.

Used on both Pleasure Craft, commercial vessels, and various industrial facilities.

Altex P40 Prepainting Cleaner is a non ionic detergent, which is designed to clean intact, painted surfaces, as well as new surfaces in preparation for repainting.
Old, painted surfaces are made “super-clean” with Altex P40 Prepainting Cleaner and the adhesion of subsequent coatings is promoted. No other preparation may be needed before repainting above water line surfaces, eliminating costly sanding, solvent wiping, abrasive sweep blasting or roughening-up of the old painted surfaces.

Altex Polyurethane Accelerator is designed to reduce the time to Hard Cure in winter temperatures in a range of Altex Polyurethane finish coats:
It is used in:
Altex Yacht & Boat Elite® Pro~Spray Linear Polyurethane.

And in the Industrial coatings:
Carbothane® 130 Clear Coat
Carbothane®949AZ (Aust. Only)
E~Line® 379
E~Line® 239