A two-component epoxy primer designed for use on aluminium sheets & extrusions, and galvanised substrates. Formulated with strontium chromate, which provides exceptional protection from filiform corrosion on aluminium surfaces.

FEATURES:

• Excellent adhesion to aluminium and galvanising
• Fast dry to recoat
• Low temperature cure down to 5°C
• Superior anti-corrosive properties

A high-performance, multi-purpose flooring epoxy coating that is easy to apply. It’s ideal for use in many flooring environments such as workshops, warehouses, factories, washrooms etc.
Available in a variety of standard colours.

FEATURES:

• Self-priming on suitably prepared concrete, or over suitably primed surfaces
• Low odour
• Low viscosity
• Low VOC / High solids
• Solvent-free
• Can be top coated with Carbothane 133 LH or E~Line series - Refer to Technical Services for further advice
• Resistant to hydraulic fluids and Skydrol once fully cured
• Tested to AS 4586:2013, Slip resistance classification of new pedestrian surface materials - Refer Certification section for more information.

A solvent-free, epoxy resin specifically formulated for use as a primer on porous concrete under Altra~Floor EF. Can be used as for coving when used in conjunction with select Altex Ancillary products – Contact Technical Services for further information.

FEATURES:

• Ideal for porous cementitious surfaces
• Low viscosity
• Zero VOC / High solids
• Solvent-free

A rapid dry/quick cure 100% solids penetrating epoxy sealer designed for use where less than ideal surface preparation is attainable or where surfaces have inherent porosity or surface weakness. It has a very low viscosity which allows it to wick into and bond porous substrates and residual rust into a tough epoxy composite. It may be applied to residual rust, degraded or new concrete, fibre-reinforced cement, and timber.

FEATURES:

• Excellent wetting properties
• 100% solids
• Rapid cure
• Low temperature cure as low as 4°C
• Ideal for marginally prepared steel
• Easy application by brush, roller, or low atomisation spray
• Can be used to seal asbestos
• Suitable for below waterline applications on marine vessels when used underneath a high build epoxy barrier system
• Approved for use in food & dairy processing plants

Made to Order or imported lines subject to availability.

A two-pack low VOC, waterborne epoxy gloss finish. The cured film is non-yellowing with high surface hardness and excellent flexibility. It exhibits excellent adhesion and water resistance and is tolerant of application over damp surfaces. It has excellent solvent resistance which makes it very resistant to graffiti. Self-priming over concrete, plaster, and fibre cement substrates.
Recommended for interior use or in-service conditions not directly exposed to extended periods of sunlight.
The low VOC and exceptionally low odour makes it an ideal coating for food process areas, hygiene areas and laboratories.

FEATURES:

• Brushing and rolling properties are similar to single pack waterborne paints
• Moisture tolerant application over damp surfaces
• Quick tack-free and recoat time giving the potential for multiple coats to be applied in a single day
• High surface hardness with excellent resistance to abrasion
• Excellent resistance to chemicals, solvents, and water
• Tenaciously adheres to a wide range of surfaces
• Can be steamed clean or power-washed
• The chemical resistance is similar to conventional solvent borne epoxies
• Available in pastel tone colours
• Approved for use in food & dairy processing plants

Penetrating primer/sealer for use on concrete substrates and Carboline Pyrocrete Fireproofing products. It performs extremely well in sealing cementitious surfaces and is designed to receive a variety of different generic types of finish coats. Some recommended uses of 1340 include the use as a curing compound or form release agent. When applied to “green” concrete it will retard the escape of moisture during the cure period. It is also excellent for use as a form release coating on plywood or steel forms.

FEATURES:

• Exceptional wetting characteristics
• Low stress, highly flexible film
• Very high solids
• Low odour
• Approved for use in food & dairy processing plants (refer to "Approvals NZ/AU" section)
• Compatibility with other coatings & membranes makes 1340 ideal for use as a curing membrane in concrete tanks & bunds
• Also used as moisture barrier coating over Thermo-Lag EPFP systems
• User-friendly brush & roller application

Fast cure isocyanate-free epoxy-acrylic gloss coating for industrial and marine and off-shore applications where use of polyurethane coatings is banned or undesirable.

FEATURES:

• Isocyanate free
• Early through-curing
• User friendly wet edge characteristics - cuts over-spray ‘flashing’
• Excellent colour and gloss** retention
• Good chemical resistance
• Good chalk resistance
• Excellent durability
• Excellent aged self re-coat

** metallic colours are not gloss and gloss level may be colour dependent

A high performance, immersion grade (fresh & salt water) chemically cured epoxy primer. Suitable for use over suitably prepared mild steel, galvanised steel, other non-ferrous metals, and most GRP substrates.

FEATURES:

• Excellent primer for water and many aqueous chemicals immersion service when topcoated with an approved finish
• Excellent adhesion to difficult substrates
• Excellent holding primer
• Excellent corrosion resistance
• Complies with AS/NZS 3750.13 (2 pack epoxy primer), Types 1, 2 & 3.
• Approved for use in NZ Food Processing Plants
• Good abrasion resistance
• Very good aged re-coatability
• Resists splash and spillage or fumes of a wide range of chemicals
• Easy application by brush, roller or spray
• Ideal tie-coat over inorganic zincs
• Versatile - can be used on most substrates under many different types of topcoat
• Long pot-life
• Excellent maintenance touch-up primer for hand-cleaned substrates
• A user-friendly primer for epoxy or polyurethane systems in environments not suited to zinc primers due to acidic or alkaline fallout or splash & spill
• Excellent tie-coat over high build epoxies as an extended 2-3 day recoat window with Sea~Barrier Antifoul series – Carboguard 504 Grey is preferred. Refer to Technical Services for further advice

Availability: Australia only

A high performance, immersion grade (fresh & salt water) chemically cured, zinc phosphate epoxy primer. Suitable for use over suitably prepared mild steel, galvanised steel, other non-ferrous metals, and most GRP substrates.

FEATURES:

• Excellent adhesion to difficult substrates
• Excellent holding primer
• Excellent corrosion resistance
• Complies with AS/NZS 3750.13 (2 pack epoxy primer), Types 1, 2 & 3.
• Good abrasion resistance
• Very good aged re-coatability
• Resists splash and spillage or fumes of a wide range of chemicals
• Easy application by brush, roller or spray
• Versatile - can be used on most substrates under many different types of topcoat
• Long pot-life
• Excellent maintenance touch-up primer for hand-cleaned substrates
• A user-friendly primer for epoxy or polyurethane systems in environments not suited to zinc primers due to acidic or alkaline fallout or splash & spill
• Excellent tie-coat over high build epoxies as an extended 2-3 day recoat window with Sea~Barrier Antifoul series. Refer to Technical Services for further advice

An all-purpose immersion-grade epoxy that has a variety of attributes including low-temperature cure, surface tolerance, fast recoat times, moisture tolerance during application and cure, and excellent corrosion protection. Can be used direct to metal as a corrosion resistant primer or as an intermediate coating over other primers. Suitable for both maintenance and new construction projects due to its excellent surface wetting characteristics and quick cure for handling. May also be used for immersion in fresh or salt water (marine) exposures.

FEATURES:

• Low temperature cure (-7°C)
• Excellent corrosion protection
• Excellent application characteristics
• Fast recoat times
• Moisture tolerant during application
• Extended self recoat window for normal atmospheric exposures (6 month self recoat)
• Approved for use in food & dairy processing plants
• Tested & approved primer under Nullifire intumescent base-coats

Made to Order or imported lines subject to availability.

High performance immersion grade epoxy that is designed as a liner for potable water tanks. This coating exhibits moisture tolerance during application, low temperature cure capability, and fast cure response for quick return to service. Product is self-priming on steel and is normally applied in two coats. Formulated for application at 120 to 180 microns DFT per coat for potable use.

FEATURES:

• Very good flexibility – resists chipping and aged embrittlement
• Lighter weight – 13% lighter than most similar coatings
• Versatile surface tolerant coating
• AS/NZS 4020 Potable Water Approval
• Lower viscosity allows application at higher solids (less thinning) and reduced VOC at application
• Fast dry to recoat
• Low temperature cure to below freezing; -5°C
• Reduced HAPS and Low VOC

A multi-purpose, advanced technology coating suited to marine and industrial applications. Suitable for atmospheric and many immersion exposures. The DTM properties make it a versatile coating in maintenance and new work applications. Syntactic foam modification gives it unique thermal shock resistance and flexibility.

FEATURES:

• Very good flexibility – resists chipping and aged embrittlement
• Versatile surface tolerant coating
• Suitable for application over surfaces prepared by water-jetting
• Good adhesion to tight rust - especially when used in conjunction with Rustbond PS or Altra~Lock 576
• Tolerant to surface dampness - particularly when brush/roller applied
• Self-priming (DTM) for many applications
• Fast dry to recoat
• Excellent dry to handling properties
• Suitable for fresh and salt water immersion
• Low temperature cure to below freezing; down to -5°C
• Reduced HAPS and Low VOC
• Cleaner colours and improved colour stability

A glass-flake filled, multi-purpose,advanced technology coating suited to marine and industrial applications. Suitable for atmospheric and many immersion exposures. The DTM properties make it a versatile coating in maintenance and new work applications. Syntactic foam modification gives it unique thermal shock resistance and flexibility. Glass flake reinforcement enhances film strength, impact resistance and barrier properties.

FEATURES:

• Excellent physical and barrier properties
• Versatile surface tolerant coating
• Good adhesion to tight rust - especially when used in conjunction with Rustbond PS or Altra~Lock 576
• Tolerant to surface dampness - particularly when brush/roller applied
• Fast dry to recoat
• Excellent dry to handling properties
• Suitable for fresh and salt water immersion
• Low temperature cure to below freezing; down to -5°C
• Reduced HAPS and low VOC
• Cleaner colours and improved colour stability

Made to Order or imported lines subject to availability.

An ideal high performance, high build coating for any service or structure, marine or industrial, where water or corrosion resistance is required.
Has excellent proven long-term service case histories for marine hull externals, above & below water, and as a lining for hydro penstocks, gates, and similar permanently immersed structures.
Carboguard 640 is the barrier coating of choice under Sea~Barrier 1000 and 3000 antifoulings.

FEATURES:

• Excellent barrier protective properties
• Recommended for permanent fresh & salt water immersion
• Exceeds performance of coal tar epoxy coatings
• Over 35 years failure-free case history in permanent fresh-water immersion service
• Good abrasion resistance
• High volume solids
• Suitable for use on concrete surfaces
• Can be self-priming
• Easy application - thick films may be applied in one application by airless spray
• Non-bleeding

This fast cure high build polyaspartic coating provides excellent corrosion protection as well as long term weatherability in just one coat. It can be applied direct to metal (DTM) at 150 to 250 microns dry film thickness (DFT) to eliminate the need for typical primers and/or intermediate coats.
This significantly speeds up the painting process, saves labour, and saves money without sacrificing performance. If even better corrosion protection is desired it can be applied over our time proven Carbozinc or Carboguard primers.

FEATURES:

• Fast cure speeds the painting process
• High build, 150 to 250μm DFT per coat
• Excellent corrosion protection
• Meets ISO 12944-6 C3 High, one coat applied DTM
• Saves significant time, labour and money
• Excellent weathering
• Exceeds SSPC Coating Specification No. 39 Level 3A, highest level for aliphatic polyurea
• Exceeds SSPC Coating Specification No. 36 Level 3A, highest level for aliphatic polyurethane
• Very good flexibility and elongation
• Excellent abrasion and impact resistance
• Excellent wetting and adhesion
• Extremely durable to help provide long service life
• Low VOC and low HAPS
• Indefinite recoatability
• Successful case history for use as a quick-turn line marking system. Refer to your local representative for further information.

Thin film, high gloss finish with exceptional weathering performance characteristics. Used extensively in virtually all industrial markets including marine exposure where ultra durable colours are desired. Carbothane 130 Clear Coat provides a smooth, high gloss durable finish that provides superior resistance to colour fade of basecoats.

FEATURES:

• High solids, low VOC content
• Excellent weatherability
• Advanced HALS (Hindered Amine Light Stabilisers) & UV absorber technology
• Superior impact and abrasion resistance
• Excellent chemical resistance
• Excellent resistance to graffiti removers
• Tested and in compliance to Main Roads WA - Specification 908 and NZTA (Waka Kotahi) - Specification S10 for Anti-Graffiti Coatings
• Approved for use in food & dairy processing plants

High build, low sheen finish that has excellent resistance to corrosion, chemicals and abrasion. Suitable for application over a number of Carboline primers and intermediates, this material provides very good weathering performance in a broad range of colours

FEATURES:

• Outstanding performance properties in both mild and aggressive environments
• High build; suitable for many two-coat systems
• Approved for use in food & dairy processing plants
• Application by spray, brush or roller
• Indefinite recoatability
• VOC compliant to current AIM regulations

Thin film, high gloss finish with exceptional weathering performance characteristics. Used extensively in virtually all industrial markets, Carbothane 134 HG provides a smooth, durable finish that has superior resistance to corrosion, abrasion and chemical exposure.

FEATURES:

• High solids, low VOC content
• Excellent weatherability
• Exceeds SSPC Paint 36 specification for a Level 3 urethane
• Conforms to the requirements of AS/NZS 3750.6:2009, Type 1 "Paints for Steel Structures - Full Gloss Polyurethane (two pack)"
• Approved for use in food & dairy processing plants (refer to "Approvals NZ/AU" section)
• Very good aged re-coatability
• Excellent flow characteristics allow for application by spray or roller
• Superior impact and abrasion resistance
• Indefinite recoatability

Made to Order or imported lines subject to availability.

Carboxane 2000 is an isocyanate-free, ultra-durable coating that provides outstanding colour and gloss retention as well as excellent corrosion protection for exterior exposures. When used over a suitable primer (as a two coat system) Carboxane 2000 provides the barrier, corrosion resistance properties, and weatherability normally achieved with a three-coat system (primer, epoxy intermediate with an acrylic-polyurethane finish) for most environments. This significantly speeds up the painting process, saves labour, and saves money without sacrificing performance. This tightly cross-linked film utilises a UV-resistant siloxane binder resulting in a finish with excellent corrosion protection and weathering performance that far exceeds aliphatic polyurethanes.

FEATURES:

• Isocyanate free
• Exceptional weatherability
• Outstanding colour and gloss retention
• Exceeds SSPC Coating Specification No. 36 Level 3A
• Excellent corrosion protection
• Meets ISO 12944 C3 High and C4 Medium, one coat applied at 125 to 175 microns DFT
• High build, 75 to 175 microns DFT
• Saves significant time, labour, and money
• Long service life
• VOC compliant
• Excellent durability
• Good flexibility and abrasion resistance
• Long pot life

Made to Order or imported lines subject to availability.

Carboxane 2000 Satin is a premium, ultra-durable coating that provides outstanding colour and gloss retention as well as excellent corrosion protection for exterior exposures. When used over a suitable primer (as a two coat system) Carboxane 2000 Satin provides the barrier, corrosion resistance properties, and weatherability normally achieved with a three-coat system (primer, epoxy intermediate with an acrylic-polyurethane finish) for most environments. This significantly speeds up the painting process, saves labour, and saves money without sacrificing performance.

FEATURES:

• Isocyanate free
• Exceptional weatherability
• Outstanding colour and gloss retention
• Exceeds SSPC Coating Specification No. 36 Level 3A
• Excellent corrosion protection
• Meets ISO 12944 C3 High and C4 Medium, one coat applied at 125 to 175 microns DFT
• High build, 75 to 175 microns DFT
• Saves significant time, labour, and money
• Long service life
• VOC compliant
• Excellent durability
• Good flexibility and abrasion resistance
• Class A Flame Spread (ASTM E84)
• Long pot life

Time-tested corrosion resistant primer that provides excellent corrosion protection to steel in some of the harshest environments. For over five decades, Carbozinc 11 has been the industry standard for high-performance inorganic zinc protection on steel structures worldwide.

FEATURES:

• Meets Class B slip co-efficient and creep testing criteria for use on faying surfaces
• Rapid cure. Dry to handle in 45 minutes at 16°C (60°F) and 50% relative humidity
• Low temperature cure down to -18°C
• High zinc loading
• Meets FDA requirements
• Zinc supplied meets ASTM D520 (Type II)
• Meets SSPC Paint 20 Type I, Level 1 for zinc content
• Complies with the composition and performance requirements of AS/NZS 3750.15, Type 4 and AS 4848.1 "Single Coat Inorganic Zinc Silicate"
• Very good resistance to salting
• May be applied with standard airless or conventional spray equipment
• Approved for use in food & dairy processing plants

Made to Order or imported lines subject to availability.

Carbozinc 11 WB is a water-based inorganic zinc rich primer that protects steel galvanically, eliminating subfilm corrosion. It meets VOC regulations while providing the proven performance of silicate zinc rich technology. It may be used as a primer under many different types of topcoats.

FEATURES:

• Excellent corrosion protection
• High zinc loading per square foot
• Zero VOC
• Good resistance to salting
• Fast curing, quick handling
• Excellent application characteristics (less likely to pump packing or tip plugging)
• Meets Class B slip coefficient* and creep testing criteria for use on faying surfaces
• Conforms to AS/NZS 3750.15 Type 3

A high performance, two component, organic zinc-filled primer specifically formulated to provide corrosion protection to steel surfaces in salt and weathering environments. It has good surface tolerant characteristics where steel surface preparation may be less than ideal. It may also be used for the repair of aged inorganic zinc-rich coatings or galvanised steel surfaces.

FEATURES:

• Exceptional corrosion resistance
• Extremely high zinc loading - 90% by weight in dry film
• Provides excellent cathodic protection
• Excellent adhesion to commercial blast cleaned surfaces
• Excellent for repairs to inorganic zinc silicate primers and aged/deteriorated galvanising
• Meets the requirements of AS/NZS 3750.9, Type 2 Organic Zinc Rich
• Conforms to the composition and performance requirements of SSPC-Paint 20 Type II Organic
• As a brush applied maintenance primer tolerant to traces of surface moisture
• As a holding / weld-through primer when applied less than 25 microns dry

NEW 4:1 Ratio

A high-solids, zinc-filled epoxy primer for corrosion protection of structural steel in salt and weathering environments. This high performance primer has quick cure-to-topcoat characteristics for in-shop applications and quick turnaround requirements in the field. It has excellent adhesion and undercutting resistance and is outstanding for use as a corrosion resistant primer for a variety of applications.

FEATURES:

• Protects steel galvanically
• Outstanding application properties
• Cures at low temperatures down to 2ºC
• Complies with AS 3750.9:1994 Type 2 Organic Zinc Rich
• Suitable for application over Wet Abrasive Blast cleaned surfaces
• Protects against corrosion under-cutting
• Tough and abrasion resistant film
• Ideal for severe industrial or marine environments with appropriate topcoats
• Approved for use in food & dairy processing plants

A high-solids, zinc-filled epoxy primer for corrosion protection of structural steel in highly corrosive environments including offshore, marine and industrial. This low VOC, HAPs compliant primer has quick cure-to-topcoat characteristics for in-shop applications and quick turnaround capabilities for the field. It has excellent adhesion and undercutting resistance and is outstanding for use as a corrosion resistant primer for a variety of applications.

FEATURES:

• Protects steel galvanically
• Outstanding application properties
• Cures at low temperatures down to 2ºC
• Tough and abrasion resistant film
• Wide use in severe industrial or marine environments

A two-component, high solids, zinc rich epoxy primer formulated for the protection of properly prepared steel substrates. Carbozinc 859 EZ2 can be applied by conventional or airless spray. Recommended where a high performance, highly corrosion resistant zinc primer is desired. Typical applications include structural steel, tanks, piping, equipment and other miscellaneous parts in industrial or architectural projects.

FEATURES:

• Excellent application properties
• Tough abrasion resistant film
• Excellent adhesion & undercutting resistance
• Superior corrosion resistance
• Meets VOC (Volatile Organic Content) regulations, <335 g/litre
• Fast drying for recoat
• Meets or exceeds SSPC Paint System 20 Level 3 (2002)
• Excellent film forming properties eliminate topcoat blistering
• Excellent resistance to salting on weathering exposure

Encapsulation Sealer-15, a low VOC epoxy primer/sealer specifically designed to seal porous/ fibrous substrates. Not only is it user-friendly, but it also accepts a variety of commercial and decorative topcoats, allowing for versatile finishing options. This product offers enhanced durability with less requirements for surface preparation on encapsulating projects. Meeting ASTM 1494-12 standards, classifying it as a bridging encapsulant. Reliable performance to protect and preserve various surfaces effectively. Encapsulating fibre containing surfaces is a crucial step in the safe removal process by sealing off coated surfaces to mitigate the release of harmful fibres into the air, significantly reducing risks during removal, allowing professionals to work more efficiently.

FEATURES:

• Excellent wicking characteristics resulting in very good adhesion to a variety of substrates.
• Surface tolerant during application and cure, enabling application over aged coatings and both single pack and two pack systems.
• Very low VOC, less than 100 g/l.
• Low odour - beneficial for compliance in many stringent locations.
• Low temperature cure with Epoxy Accelerator down to 1.7°C.
• Suitable for year round application.
• Tolerates higher dry film thickness (DFT) range than typical porous surface sealers.
• Translucent blue colour to easily identify coated surfaces.

High gloss, high performance, two component, chemically cured polyaspartic urethane designed for use in areas where maximum gloss and colour retention are required.

FEATURES:

• Polyaspartic acrylic technology provides exceptional gloss and colour retention
• Outstanding cosmetic properties
• Outstanding abrasion resistance
• Excellent durability due to high flexibility and toughness
• Exceptional retention of cosmetic properties due to high UV resistance
• Outstanding chemical resistance
• Light colours along with a finish coat of Carbothane 130 Clear Coat may be used as an anti-graffiti system due to the excellent solvent resistance - refer also to and Easy~Clean SX Additive
• High volume solids - Low VOC
• Available with Ultra-Fresh Antimicrobial Additive where hygienic germ-free coating systems are required.
• Tested and in compliance to Main Roads WA - Specification 908 and NZTA (Waka Kotahi) - Specification S10 for Anti-Graffiti Coatings
• Approved for use in food & dairy processing plants

Fast cure, high gloss, aliphatic polyurethane which is ideal for use where a polyurethane finish is specified and where rapid drying is desirable. It will provide good gloss and colour retention as well as resistance to moderate to severe corrosive environments for:

• Structural Steel
• Shop application
• Chemical processing industry
• Pulp and paper industry
• Dairy industry
• Bridges and storage tanks
• Fishing vessels
• Off-shore structures
• Shoreside facilities

FEATURES:

• Fast dry to handling - increased throughput
• Rapid dry to recoat
• Good gloss retention and colour retention
• Good chemical resistance
• Good abrasion resistance
• Excellent durability due to high flexibility and toughness
• Good retention of cosmetic properties due to high UV resistance
• Good resistance to marring, chipping, and scratching
• Wide colour selection
• Excellent aged recoatability
• Approved for use in food & dairy processing plants

Isotal is a premium quality alkyd gloss enamel which is designed to protect and give good appearance to:

• Suitably primed mild steel and other metal surfaces
• Tank exteriors
• Bridges and pipes
• Marine exterior areas such as freeboards, decks, houses, and superstructures
• Marine interior areas such as engine rooms, passageways, and equipment
• Farm equipment / restoration projects

FEATURES:

• Durable high gloss finish
• Interior or exterior usage
• Marine quality
• Excellent weathering properties
• Excellent flow and levelling
• Good corrosion resistance in normal - mildly acidic fume areas
• High hiding
• Washable and scrubbable
• Good abrasion resistance
• Easy application by brush, roller, or spray
• Safe – All colours lead and chrome free
• Available with Ultra-Fresh Antimicrobial Additive where hygienic germ-free coating systems are required

A premium quality, single pack alkyd undercoat which is normally used under Isotal Enamel on properly primed surfaces. It can be used in areas such as:

• Properly primed masonry, steel, and other metal surfaces
• Marine exterior areas such as freeboards, decks, houses, and superstructures
• Marine interior areas such as engine rooms, passageways, and equipment
• Wooden structures
• Tie coat over aged enamel systems prior to re-finish coating

FEATURES:

• Suitable for interior and exterior applications
• Marine quality
• Excellent hiding power
• Easy application by brush, roller, or spray
• Sandable
• Removes minor surface defects prior to finish coating

Single component premium quality primer based on proprietary synthetic, immersion grade alkyd resins. An excellent protective primer for most substrates in marine and industrial exposures.
It is recommended for use on:

• Agricultural equipment
• Commercial charter yachts, launches and fishing vessels (above and below the waterline)
• On site touch-up work-handrails etc
• Restoration of timber joinery

FEATURES:

• Applied directly to suitably prepared steel, galvanised steel, wood and GRP
• Excellent adhesion
• Above the waterline - overcoat with a sandable undercoat such as Altex Isotal Undercoat and topcoat with Altex Isotal Enamel
• Below the waterline – in multiple coats as part of a marine protective system where it is normally overcoated with Sea~Barrier® 3000 antifouling
• Interior or exterior usage
• Marine quality
• Easy application by brush, roller, or spray
• Sandable

A fast drying, economical, steel primer designed for use in engineering fabrication shops. Pre~Fab is suitable as a stand-alone coating in mild interior environments and provides good protection to structural steel in moderate exterior environments when topcoated with compatible alkyd or acrylic coatings. Pre~Fab is the primer of choice for SSPC-SP 2 hand tool cleaned structural steel to be enclosed within wall framing.

FEATURES:

• Fast drying action allows rapid handling of coated steel at 25°C
• Modified zinc phosphate anti-corrosive pigmentation
• Higher Zinc Phosphate content than other shop primers
• Free of chromates and other heavy metal compounds
• Suitable for acrylic and alkyd topcoats
• Very economic cost per square metre
• Can be applied using conventional spray equipment as well as airless spray
• Highly recoatable with itself or other alkyd undercoats or finish coat

RIPO (Rust Inhibiting Penetrating Oil) is a drying “wetting oil” pre-treatment, for use on hand or power tool cleaned surfaces and sometimes with brush blasted surfaces, prior to application of High Build Rust Barrier and other alkyd coatings. RIPO forms a water-resistant film and is useful in protecting steel from condensation corrosion as encountered on:

• Interior of vehicle doors and body panels
• Underside of surfaces on appliances, such as freezers and washing machines
• Marine topsides
• Excellent rust treatment as part of a single pack coating system on; agricultural machinery and various pieces of equipment, trailers, structural steel

FEATURES:

• Thin penetrating liquid which dries to a non-tack film
• Anti-corrosive
• Water resistant
• Easy application
• Multi-purpose
• Can be overcoated with High Build Rust Barrier or Multi~Bond Primer
• Single pack-ready to use

Rustbond PS is a very low VOC epoxy primer/sealer that combines outstanding surface tolerance characteristics over marginally prepared substrates and user-friendly features. It accepts a variety of topcoats and can help save time and money by minimising surface preparation requirements for new construction, maintenance and overcoating projects. Rustbond PS has good pot life at higher temperatures to help minimise waste and also cures at low temperatures down to 1.7°C with Epoxy Accelerator so you have one Rustbond product for year-round application.

FEATURES:

• Excellent wicking characteristics resulting in very good adhesion to a variety of substrates
• Low stress during application and cure, can be applied over aged coatings and tight rust
• Universal primer and tie-coat
• Very low VOC, less than 100 g/l, and low odour for compliance in many stringent locations
• Low temperature cure with Epoxy Accelerator to extend the painting season
• Good pot life in hotter weather without Epoxy Accelerator, one Rustbond PS for year-round application
• User-friendly application with brush, roller, and spray
• Tolerates higher dry film thickness (DFT) range, easier to apply
• Excellent sealer for metallising and thermal sprayed aluminium (TSA)