Made to Order or imported lines subject to availability.

A spray-grade, economical, epoxy-based repair mortar, patching and surfacing compound that exhibits excellent bond strength to concrete and other masonry surfaces. It is ideally suited for resurfacing deteriorated concrete in wastewater environment. Topcoated with Carboline’s lining systems provides protection from acid attack from H2S or MIC. Unique spraygrade (SG) formulation speeds application properties for quick turnaround projects.

FEATURES:

• Epoxy modification improves chemical resistance for wastewater environments
• Trace VOC - <12 mg / lt, EPA Method 24)
• Water based, low odour
• Excellent film strength, abrasion, and impact resistance
• Easily topcoated to provide additional chemical resistance or appearance
• Self-priming over concrete
• Aggregate reinforced

Made to Order or imported lines subject to availability.

High performance immersion grade epoxy that is designed as a liner for potable water tanks. This coating exhibits moisture tolerance during application, low temperature cure capability, and fast cure response for quick return to service. Product is self-priming on steel and is normally applied in two coats. Formulated for application at 120 to 180 microns DFT per coat for potable use.

FEATURES:

• Very good flexibility – resists chipping and aged embrittlement
• Lighter weight – 13% lighter than most similar coatings
• Versatile surface tolerant coating
• AS/NZS 4020 Potable Water Approval
• Lower viscosity allows application at higher solids (less thinning) and reduced VOC at application
• Fast dry to recoat
• Low temperature cure to below freezing; -5°C
• Reduced HAPS and Low VOC

A multi-purpose, advanced technology coating suited to marine and industrial applications. Suitable for atmospheric and many immersion exposures. The DTM properties make it a versatile coating in maintenance and new work applications. Syntactic foam modification gives it unique thermal shock resistance and flexibility.

FEATURES:

• Very good flexibility – resists chipping and aged embrittlement
• Versatile surface tolerant coating
• Suitable for application over surfaces prepared by water-jetting
• Good adhesion to tight rust - especially when used in conjunction with Rustbond PS or Altra~Lock 576
• Tolerant to surface dampness - particularly when brush/roller applied
• Self-priming (DTM) for many applications
• Fast dry to recoat
• Excellent dry to handling properties
• Suitable for fresh and salt water immersion
• Low temperature cure to below freezing; down to -5°C
• Reduced HAPS and Low VOC
• Cleaner colours and improved colour stability

A glass-flake filled, multi-purpose,advanced technology coating suited to marine and industrial applications. Suitable for atmospheric and many immersion exposures. The DTM properties make it a versatile coating in maintenance and new work applications. Syntactic foam modification gives it unique thermal shock resistance and flexibility. Glass flake reinforcement enhances film strength, impact resistance and barrier properties.

FEATURES:

• Excellent physical and barrier properties
• Versatile surface tolerant coating
• Good adhesion to tight rust - especially when used in conjunction with Rustbond PS or Altra~Lock 576
• Tolerant to surface dampness - particularly when brush/roller applied
• Fast dry to recoat
• Excellent dry to handling properties
• Suitable for fresh and salt water immersion
• Low temperature cure to below freezing; down to -5°C
• Reduced HAPS and low VOC
• Cleaner colours and improved colour stability

Made to Order or imported lines subject to availability. 

Suitable for single coat applications in areas such as a penstock lining at film thicknesses ranging between 400 and 1500 microns. Suitable for service in various immersion environments including industrial wastewater, slurry tanks, sea or fresh water, on buried structures, and on high wear surfaces in atmospheric exposure.

FEATURES:

• High film builds in a single coat – 0.4mm to 1.5mm
• Extensive case history in hydro penstocks & scroll casings, along with industrial wastewater processing
• Positive cure, even at low temperatures
• Highly abrasion resistant
• Unique flexibilised formulation imparts excellent impact resistance
• May be used on buried structures, structures immersed in fresh or salt water, and for atmospheric exposure
• Suitable for use with cathodic protection systems – impressed current or anode types
• Easy application qualities using properly heavy-duty airless spray equipment

Graded silica blend for epoxy putty / mortar mixes

Made to Order or imported lines subject to availability. 

Glass flake-filled coating with dense cross-linking that exhibits excellent overall chemical resistance to a variety of aggressive chemicals. Glass reinforcement provides added abrasion resistance, permeation resistance and internal reinforcement. 1205 exhibits very good acid resistance. Excellent for use as a lining for tanks or pipes in process facilities where hot water or abrasive conditions exist.

FEATURES:

• Excellent resistance to ethanol, gasoline, jet fuels and solvents
• Excellent abrasion resistance
• Excellent thermal shock resistance (-17 to 150°C)
• Excellent resistance to deionized or demineralised water up to 95°C
• Excellent resistance to crude oil up to 121°C
• Excellent for crude oil storage and transportation up to 121°C
• Recommended for CS-1,3,4 and SS-1,2,3 systems of NACE SP0198 Standard Practice for coatings to control Corrosion Under Insulation (CUI)
• Approved for use in food & dairy processing plants

Made to Order or imported lines subject to availability.

Phenoline 353 LT is a highly cross-linked epoxy lining with extraordinary overall chemical resistance and versatility. It has a unique blend of resins that make it highly resistant to a variety of aggressive cargoes like gasoline, gasoline blends, biodiesel, fuel oils, and others. It can be used in both acidic and high temperature caustic exposures. Markets served are terminals, refineries, petrochemical, wastewater, railcar linings, subsea oil and gas equipment, and many others. This low temperature cure formulation allows application and curing down to 2°C.

FEATURES:

• Outstanding overall chemical resistance
• Dense, highly cross-linked film for superior barrier protection
• Excellent abrasion resistance and toughness
• Well-suited for hydrocarbon exposures
• Cures down to 2°C
• Meets NORSOK System 7C requirements for subsea equipment up to 180°C
• Approved for use in food & dairy processing plants

Made to Order or imported lines subject to availability. 

This product is a solvent-free, high performance epoxy coating designed as an internal tank, valve and pipe lining for chemical or other commodity storage. It is a unique blend of resins and curing agents that allow batch mixing for ease of application. Plural component spray equipment is not required. The product is blush resistant and is typically applied at film thicknesses of 500 microns or thicker as needed (tank floors). It can handle exposures typically seen in the oil and gas industries; crude oils and fuels. It is resistant to NGL condensates, produced water, brines, industrial process water, waste water, and sewage. Ideal for municipal wastewater and water treatment facilities.

FEATURES:

• Batch mix formulation, single leg airless spray
• High impact resistance
• Superior adhesion to steel
• Excellent resistance to water and salt water
• Resistance to a broad range of fuels including ethanol
• Passes EI 1541 requirements for internal protective coating systems used in aviation fuel handling systems, including the jet fuel gum test
• Resistant to hot water up to 82°C
• Excellent abrasion resistance and flexibility
• Can be applied down to 2°C
• Can be applied as a single or multi-coat system
• NSF/ANSI 61 compliant for use in potable water tanks, pipes, and valves.*
• Certified by UL to meet the drinking water criteria of NSF/ANSI/CAN 600
• Non-blushing with a long recoat window
• Tested and approved to AS/NZS 4020:2018
• Low odour

Contact Carboline Technical Service for approved dimensions.
*Valid when manufactured at a certified location.

Made to Order or imported lines subject to availability.

This product is a solvent-free, high performance epoxy coating specifically designed as a pit filling primer with ideal flow properties allowing it to wet-out and fill moderate to severe pitting on steel tank bottoms. It's unique formula allows batch mixing for ease of application. With an appropriate lining, it can withstand exposures typically seen in the oil and gas industries. It is resistant to crude oil, NGL condensates, produced water, brines, and industrial process water.

FEATURES:

• Highly penetrating formula to handle severe pitting
• Blast hold protection
• Batch mix formulation, single leg airless spray
• Superior adhesion to steel
• Excellent abrasion resistance and flexibility
• Can be applied down to 2°C
• Can be used with multiple lining systems
• Non-blushing with a long recoat window
• Convenient packaging for batch mix
• Tested and approved to AS/NZS 4020:2018 when topcoated with Phenoline Tank Shield (refer to data sheet)
• Low odour

Made to Order or imported lines subject to availability.

Environmentally friendly, advanced hybrid technology, plural-component applied coating used as a lining for water, wastewater, manholes, penstocks, dam gates, pipelines and other aggressive immersion applications. Provides protection against microbiologically induced corrosion (MIC) and hydrogen sulfide corrosion found in wastewater treatment service. Ultra high build product designed to be applied at high thickness in one coat application. 

FEATURES:

• High film build (5000 microns / 5mm plus) in one coat
  
• Complies with Greenbook
• UL approved for potable water*
• Cold temperature cure
• Fast cure and walk on time
• Excellent barrier properties, low permeability
• Can be used to resurface highly deteriorated concrete
• Bridges normal shrinkage cracks in concrete
• True monolithic film on steel and concrete
• Encapsulates rivets, bolts, and edges in one coat
• Outstanding abrasion, impact and tear resistance
• Combines polyurethane and polyurea technologies to form a hybrid polyurethane

*Valid if manufactured at a certified location.

Made to Order or imported lines subject to availability. 

Reactamine Joint Seal FC is a 2-component 100% solids, polyurea-based joint sealant that is self levelling and cures in approximately 30 minutes. It works equally well with asphalt and concrete and protects interior horizontal concrete expansion and control joints from spalling, chipping and breakdown.
This product can be applied at temperatures ranging from -18° to 65°C and possesses excellent chemical resistance, water resistance and thermal stability at both high and low temperatures.

FEATURES:

• 100% solids; zero VOC
• Fast cure times
• USDA compliant for non-direct food contact
• Has a functional temperature range of -18°C to 121°C
• Excellent water resistance, chemical resistance, and thermal stability at high & low temperatures
• Works well with asphalt or concrete

Made to Order or imported lines subject to availability.

Solvent-free patching compound used for repairing pits, cracks and voids in steel, concrete, wood and other surfaces. Has the unique ability to be mixed, applied and cured underwater.

FEATURES:

• Designed for underwater and other wet applications
• Can be applied up to 50 mm (2") in thickness
• Self-priming on most surfaces and over most generic types of coatings
• Rapid cure characteristics
• VOC compliant to current AIM regulations