Carboguard® 504 is an inert non-inhibitive anti-corrosive modified polyamide cured epoxy primer.

• Excellent primer for water and many aqueous chemicals immersion service when top-coated with an approved finish
• Excellent adhesion to difficult substrates
• Excellent holding primer
• Excellent corrosion resistance
• Complies with AS/NZS 3750.13 (2 pack epoxy primer), Types 1, 2 & 3.
• Good abrasion resistance
• Very good aged re-coatability
• Resists splash and spillage or fumes of a wide range of chemicals
• Easy application by brush, roller or spray
• Ideal tie-coat over inorganic zincs
• Versatile - can be used on most substrates under many different types of topcoat
• Long pot-life
• Excellent maintenance touch-up primer for hand-cleaned substrates

A user-friendly primer for epoxy or polyurethane systems in environments not suited to zinc primers due to acidic or alkaline fallout or splash & spill.

Availability: Australia

Carboguard® 504 ZP is a zinc phosphate modified inhibitive anti-corrosive polyamide cured epoxy primer

Carboguard® 504 ZP may be applied over suitably prepared mild steel, non-ferrous metals and other substrates as specified

• Excellent adhesion
• Excellent holding primer
• Excellent corrosion resistance
• Complies with AS/NZS 3750.13 (2 pack epoxy primer), Types 1, 2 & 3.
• Good abrasion resistance
• Very good aged re-coatability
• Resists splash and spillage or fumes of a wide range of chemicals
• Easy application by brush, roller or spray
• Versatile - can be used under many different types of topcoat
• Long pot-life
• Excellent maintenance touch-up primer for hand-cleaned substrates

Made to Order or imported lines subject to availability.

A spray-grade, economical, epoxy-based repair mortar, patching and surfacing compound that exhibits excellent bond strength to concrete and other masonry surfaces. It is ideally suited for resurfacing deteriorated concrete in wastewater environment. Topcoated with Carboline’s lining systems provides protection from acid attack from H2S or MIC. Unique spraygrade (SG) formulation speeds application properties for quick turnaround projects

• Epoxy modification improves chemical resistance for wastewater environment
• Zero VOC
• Water based, low odour
• Excellent film strength, abrasion, and impact resistance
• Easily topcoated to provide additional chemical resistance or appearance
• Self-priming over concrete
• Aggregate reinforced

A rapid cure to topcoat epoxy with high abrasion resistance along with other valuable attributes including:

• low-temperature cure
• surface tolerance
• fast recoat times
• moisture tolerance during application and cure
• excellent corrosion protection.

Carboguard 635 HAR can be used direct to metal as a corrosion resistant primer or as an intermediate coating over other primers. It may also be used for immersion in fresh or salt water exposures, and exhibits exceptional abrasion resistance and toughness.

Made to Order - High performance immersion grade epoxy that is designed as a liner for potable water tanks. This coating exhibits moisture tolerance during application, low temperature cure capability, and fast cure response for quick return to service.
Product is self-priming on steel and is normally applied in two coats. Formulated for application at 120 to 180 microns DFT per coat for potable use.

• Very good flexibility – resists chipping and aged embrittlement
• Lighter weight – 13% lighter than most similar coatings
• Versatile surface tolerant coating
• AS/NZS 4020 Potable Water Approval (see "Approvals NZ/AU" section)
• Lower viscosity allows application at higher solids (less thinning) and reduced VOC at application
• Fast dry to recoat
• Low temperature cure to below freezing; -5°C
• Reduced HAPS and Low VOC

A multi-purpose, advanced technology coating suited to marine and industrial applications. Suitable for atmospheric and many immersion exposures. The DTM properties make it a versatile coating in maintenance and new work applications. Syntactic foam modification gives it unique thermal shock resistance and flexibility.

Link

A glass-flake filled, multi-purpose,advanced technology coating suited to marine and industrial applications. Suitable for atmospheric and many immersion exposures. The DTM properties make it a versatile coating in maintenance and new work applications. Syntactic foam modification gives it unique thermal shock resistance and flexibility. Glass flake reinforcement enhances film strength,
impact resistance and barrier properties.

Made to Order or imported lines subject to availability.

Carboguard® 640 is a high performance, two-component, modified phenalkamine, chemically cured, immersion grade epoxy barrier coating

Carboguard® 640 is an ideal high build coating for any service or structure, marine or industrial, where water or corrosion resistance is required.

Carboguard® 640 has excellent proven long-term service case histories for marine hull externals, above & below water, and as a lining for hydro penstocks and gates and similar permanently immersed structures.

Carboguard® 640 is the barrier coating of choice under Altex Sea~Barrier™ 1000, 3000 and Alloy 100Plus antifoulings

Made to Order or imported lines subject to availability. 

Suitable for single coat applications in areas such as a penstock lining at film thicknesses ranging between 400 and 1500 microns. Suitable for service in various immersion environments including industrial wastewater, slurry tanks, sea or fresh water, on buried structures, and on high wear surfaces in atmospheric exposure.

• High film builds in a single coat – 0.4mm to 1.5mm
• Extensive case history in hydro penstocks & scroll casings, along with industrial wastewater processing
• Positive cure, even at low temperatures
• Highly abrasion resistant
• Unique flexibilised formulation imparts excellent impact resistance
• May be used on buried structures, structures immersed in fresh or salt water, and for atmospheric exposure
• Suitable for use with cathodic protection systems – impressed current or anode types
• Easy application qualities using properly heavy-duty airless spray equipment

This high performance epoxy coating exhibits outstanding moisture and surface tolerance during application, low temperature cure capability, and very fast cure response for quick return to service. This makes Carbomastic 615 eminently suitable for maintenance repaint work in marginal conditions and where surface preparation is less than ideal.

It contains an inert flake reinforcement (micaceous iron oxide) to enhance film strength and performance.

• High solids, low VOC
• Low temperature cure
• Excellent wetting properties
• Excellent surface tolerance
• Excellent moisture tolerance (application)
• Fast cure response

Suitable for immersion service in fresh or salt water after 60 minute cure @ 24°C

This fast cure high build polyaspartic coating provides excellent corrosion protection as well as long term weatherability in just one coat.

It can be applied direct to metal (DTM) at 150 to 250 µms dry film thickness (DFT) to eliminate the need for typical primers and/or intermediate coats. This significantly speeds up the painting process, saves labor, and saves money without sacrificing performance. If even better corrosion protection is desired it can be applied over our time proven Carbozinc or Carboguard primers.

Chem~Bar 900™ is specifically formulated to protect metal or masonry surfaces exposed to weather, water or chemicals.

Chem~Bar 900™ may be used to protect structural steel, tanks, pipes and equipment a vast range of industries.

It's recoatable properties, highly anti-corrosive formulation and ease of application make it an ideal coating for both maintenance and new work.

• Pulp and Paper Industry
• Chemical Process Industry
• Sewage and Waste Water Plants
• Water Tanks
• Refineries
• Fertiliser Plants
• Marine Installations
• Bridges
• Power Projects
• Containers
• Shipping

E~Line 379® is a high gloss, high performance, two component, chemically cured polyaspartic urethane designed for use in areas where maximum gloss and colour retention are required.

E~Line 379® will provide excellent gloss and colour retention as well as resistance to moderate to severe corrosive environments for:

• Transportation industry
• Chemical processing industry
• Pulp and paper industry
• Dairy industry
• Bridges and storage tanks
• Light colours and clear may be used as anti-graffiti coatings due to their excellent solvent resistance - refer also to Altex Graffiti Remover and Easy~Clean SX Additive
• Outstanding abrasion resistance
• Excellent durability due to high flexibility and toughness
• Exceptional tolerance to marginal application conditions
• Exceptional retention of cosmetic properties due to high UV resistance

Reinforcing additive for a range of Carboguard epoxy coatings

Made to Order or imported lines subject to availability. 

High solids modified novalac epoxy, with excellent low temperature cure and outstanding chemical resistance.

Provides immersion grade service for a vast range of chemicals (refer Data Sheet)  in a wide range of industries:

Wastewater

Petrochemical

Industrial manufacturing / processing

Chemical transport

This product is a solvent-free, high performance epoxy coating specifically designed as a pit
filling primer with ideal flow properties allowing it to wet-out and fill moderate to severe pitting on
steel tank bottoms. It's unique formula allows simple batch mixing for ease of application. With an
appropriate lining, it can handle exposures typically seen in the oil and gas industries. It is resistant
to crude oil, NGL condensates, produced water, brines, and industrial process water.

Made to Order or imported lines subject to availability.

Environmentally friendly, advanced hybrid technology, plural-component applied coating used as a lining for water, wastewater, manholes, penstocks, dam gates, pipelines and other aggressive immersion applications. Provides protection against microbiologically induced corrosion (MIC) and hydrogen sulfide corrosion found in wastewater treatment service. Ultra high build product designed to be applied at high thickness in one coat application. 

Made to Order or imported lines subject to availability. 

Reactamine Joint Seal FC is a 2-component 100% solids, polyurea-based joint sealant that is self-leveling and cures in approximately 30 minutes. It works equally well with asphalt and concrete and protects interior horizontal concrete expansion and control joints from spalling, chipping and breakdown. This product can be applied at temperatures ranging from -18° to 65°C and possesses excellent chemical resistance, water resistance and thermal stability at both high and low temperatures

Rustbond PS is a very low VOC epoxy primer/sealer that combines outstanding surface tolerance characteristics over marginally prepared substrates and user-friendly features. It accepts a variety of topcoats and can help save time and money by minimising surface preparation requirements for new construction, maintenance and overcoating projects. Rustbond PS has good pot life at higher
temperatures to help minimise waste and also cures at low temperatures down to 1.7°C with Epoxy Accelerator so you have one Rustbond product for year-round application.