Made to Order or imported lines subject to availability.

A single pack acrylic thin film intumescent basecoat for the protection of internal and semi-exposed structural steel.

SC601 is optimised to provide 60 minutes fire resistance to ‘I’ section beams and columns, hollow columns and beams, as well as cellular beams, concrete filled hollows and solid steel rods. 90 minute and limited 120-minute protection is also available.

FEATURES:

• Competitive loadings
• Can be applied on-site or off-site
• Easy to apply by airless spray
• Suitable for exposures up to C3 environments
• Can be exposed to the weather for up to 3 months once cured provided that no standing or ponding water is allowed to form
• Optifire®+ unique traceability identifier
• Certification:
  • Certifire CF5767
  • BS476 Part 20/21
  • Cellular Beams YB5
  • EN13381-6 Concrete Filled Hollow Tubes
  • EN13881-10 Solid Steel Rods

Made to Order or imported lines subject to availability. 

A thin film intumescent coating for the fire protection of internal structural steelwork.
SC802 is optimised for up to 60 FRR fire resistance and designed for on-site application.

FEATURES:

• Fully tested and certified in accordance with BS476: Part 21: 1987
  • Certifire CF5420
• Waterborne technology
• Very low VOC: 16 g / litre
  • 84% below IEQ-3 Indoor Air Quality requirement of ≤ 100 g/litre
• Halogen-free formulation
• Low odour, user friendly
• No topseal required for interior, dry non-decorative exposures
• Rapid dry to recoat / topcoat (refer to dry time and ventilation tables overleaf)
• Other Certification:
  • Fire Propagation / Spread of Flame
    • BS476: 6/7 Class 0
  • EN13823 (SBI) and IMO smoke / toxicity
  • Certifire fully tested on cellular beams

Made to Order or imported lines subject to availability.

Certified Applicators Only. Nullifire SC902 may only be applied by trained and approved applicators; refer to Altex Coatings for approved applicator listings in your area.

Nullifire SC902 is a fast track on or off-site, low VOC, one coat high build system capable of providing up to 2 hours protection in a single coat.

FEATURES:

• Fast cure, early weather resistance, shower proof within 1 hour
• Achieves external durability with an approved top seal
• Cures below 0°C and fully dry by the following day
• Self-priming system tolerant of light rusting to steel, up to 2 weeks post blasting
• High build capability with all ratings possible in one application
• Fire rating up to 120 minutes tested to BS476 and EN13381: Part 8 and assessed to meet AS1530.4 and AS4100; ref BRANZ FAR 3997 & FAR 4292 (RBSA)
• Fast Track:
  • Conventional intumescent coating systems for 120 FRR that may take 7 days to complete can be completed in just 24 hours using Nullifire SC902

Made to Order or imported lines subject to availability.

Fireproof and ecological mortar for the passive fire protection of steel, concrete, composite concrete-steel sheet slab structural elements, fire compartmentation and fire stop partitions. Fire resistance of up to 4 hours depending on the construction system.

FEATURES

• Formulation with light high-performance fillers
• Non-combustible
• Can be sprayed by discontinuous machine to improve its performance by 15%
• Asbestos free – Complies with regulations 200/3/18/EC and RD 396/2006
• Good adhesion on different substrates/li>
• Light and low abrasion with the use of spraying equipment. Saving on consumables
• Low protection thicknesses. Saving on transport and labour
• Wide range of fire solutions

A single pack sealer designed for use as part of an approved Altex Coatings Ltd single pack, solvent borne intumescent coating system. It is applied to cured approved intumescent coatings to protect it from moisture ingress, so that steel may be stored outside with enhanced weathering properties.
It can minimise solvents in the subsequent finish coats from re-entering the approved intumescent film.
When correctly applied to partially cured approved intumescent, Pro~Seal allows residual solvents, retained within the approved intumescent to transpire through the film. Full cure (hardness at Shore D-50) may then be achieved for the intumescent film.

Pro~Seal is the first intumescent seal coat that significantly reduces those risks that can be encountered with approved single pack, solvent borne intumescent coatings:

• Solvent entrapment & resulting blistering
• Rain damage
• Solvent softening from finish coats
• Finish coat incompatibility

FEATURES:

• Rapid dry – dust free typically within 30 minutes
• Extended time to finish coat. May be left through the entire construction phase for finish coating (with suitable preparation) at project completion
• Easy to use – single component coating
• Brush, roller, or spray application
• Excellent resistance to solvents (once cured) permitting application of a wide range of two component polyurethanes for both interior and exterior exposure
• Cures well at low temperatures
• Promotes the cure of the approved intumescent coating, thus ensuring cure can be achieved with minimal risk of moisture damage
• May be finish coated with a wide range of solvent borne or water borne finish coats

Made to Order or imported lines subject to availability.

A 55 lb./ft³ (881 kg/m³) density, Portland cement based, cementitious fireproofing. It provides bothhydro carbon and cellulosic fire protection for structural steel and can also be used to upgrade the fire resistance of existing concrete. Recommended areas of application include refineries, petrochemical, pharmaceutical facilities, pulp and paper mills, offshore platforms, nuclear and conventional power plants, factories, warehouses, institutional and biomedical facilities.

FEATURES:

• Over 40 years of proven performance
• Exceptional durability and toughness
• Tested and approved for exterior use by Underwriters Laboratories Inc
• UL 1709 hydrocarbon fire rated up to 4 hours
• BS 476 hydrocarbon fire rated up to 4 hours
• ISO 22899-1 jet fire rated up to 2 hours
• ASTM E119 cellulosic fire rated up to 4 hours
• Cryogenic protection against LNG spills and immersion exposures
• Resistant to 3 bar blast overpressure
• Hose stream resistant
• Tolerant to wide range of climates
• Lightweight – one-fifth the weight of concrete for equal fire protection
• Ideal for onsite and offsite application
• Easy application by spray or trowel
• Nonflammable – during or after application
• Chloride and sulfide free – no special priming required
• Asbestos-free – complies with EPA and OSHA regulations
• Non-friable – high impact strength

Made to Order or imported lines subject to availability.

A minimum 640 kg/m³ (40 lb./ft³) density, Portland cement based, cementitious fireproofing. It provides both hydrocarbon and cellulosic fire protection for structural steel and can also be used to upgrade the fire resistance of existing concrete. Recommended areas of application include refineries, petrochemical, pharmaceutical facilities, pulp and paper mills, offshore platforms, nuclear and conventional power plants, factories, warehouses, institutional and biomedical facilities.

FEATURES:

• Cost effective fireproofing solution
• Outstanding coverage, high build
• Exceptional durability and toughness
• UL 1709 hydrocarbon fire rated up to 4 hours
• BS 476 hydrocarbon fire rated up to 4 hours
• ISO 22899-1 jet fire rated up to 2 hours
• ASTM E119 cellulosic fire rated up to 4 hours
• Cryogenic protection against LNG spills and immersion exposures
• Resistant to 3 bar blast overpressure
• Hose stream resistant
• Tolerant to wide range of climates
• Typically field applied at a 640 - 800 kg/m³ (40 - 50 lb./ft³) dry density
• Lightweight – one-fifth the weight of concrete for equal fire protection
• Easy application by spray or trowel
• Non-flammable – during or after application
• Chloride and sulfide free – no special priming required
• Asbestos-free – complies with EPA and OSHA regulations
• Non-friable – high impact strength

Made to Order or imported lines subject to availability.

A gypsum based, Spray-applied Fire Resistive Material (SFRM) designed for the fire protection of interior structural steel. Formulated and applied to meet the minimum bond strength requirements of the IBC Code listed in the “High Rise Building Section" for buildings up to 22.9m (75 feet).

A 240 kg/m³ (15 lb./ft³) SFRM intended for the fire protection of interior structural columns, beams, joists, decks, walls, roofs, girders, floors and pre-cast concrete units. It is tested and certified for fire resistance ratings up to 4 hours.

FEATURES:

• Assessed in accordance with AS 1530.4:2005
• Assessed in accordance with AS 4100
• Provides protection for I-section and hollow beams and columns up to 240 FRR (4 hours)
• Certified data available for limiting temperatures ranging from 350°C to 700°C
• Non-combustible
• Can be injected with Accelerator A-20 for fast set and increased yield (optional)
• Excellent film builds on all surfaces including columns, beams and decks.
• Applicator friendly – High film build, no alum required for increased coverage*.
• Asbestos-free – complies with EPA and OSHA regulations.
• Mineral Wool free – no airborne fibres.
• Styrene free – no toxic decomposition gases.
• Economical – Maintains project on budget.
• Design flexibility with over 100 UL designs

Made to Order or imported lines subject to availability.

Certified Applicators Only. Applicator Note: Thermo-Lag 3000-SP may only be applied by trained and approved applicators; refer to Altex Coatings for approved applicator listings in your area.

Thermo-Lag 3000-SP is a flexible, two-component epoxy Intumescent Fireproofing coating designed to provide asset integrity from the damaging effects of hydrocarbon fires. Since 1999 Thermo-Lag 3000-SP has provided fire protection in the harshest of environments, such as oil, gas, refineries, power, marine, petrochemical, and LNG facilities.
Thermo-Lag 3000-SP has been extensively and independently tested in accordance with: UL 1709, UL 2431 Category I-A, ISO 834-3, IMO FTP Code (IMO A.754(18) for H-0, H-60 & H-120 Divisions, ASTM E84, ASTM E119, ISO 20340, NORSOK M-501 5A Fire and Corrosion Testing, and NFPA 290 (extended to 150 minutes).

FEATURES:

• Provides a flexible fire protection solution to structural steelwork, process vessels, divisions and electrical raceways for 1 through 4 hours
• Lowest thickness per fire rating of any competitive epoxy intumescent coating
• Durable finish – provides a hard, durable finish resistant to normal wear & tear.
• Inherently flexible and durable formulation designed to withstand abrasion, vibration, handling, transportation and erection stresses in any climate.
• Formulated to maintain it’s flexibility, elongation and fire resistive properties throughout its service life regardless of climate.
• Engineered to resist extreme and rapid temperature cycles without cracking or disbondment.

Made to Order or imported lines subject to availability.

Certified Applicators Only. Thermo-Lag E100 S may only be applied by trained and approved applicators; refer to Altex Coatings for approved applicator listings in your area.

An epoxy intumescent fireproofing for commercial and light industrial applications. It was specifically designed with an advanced formulation to provide 1-3 hour cellulosic fire protection for structural steel beams, I-section columns, tubular columns and pipes without the need for reinforcing mesh. It provides a fast curing, aesthetically pleasing fire protection solution and is rated for both exterior and interior applications.

FEATURES:

• Certified to UL 263 / ASTM E119 / NFPA 251
• Exterior and interior rated
• High quality aesthetic finish
• Does not require reinforcing mesh
• Low thickness requirements
• High build, fast recoat
• Saves application time, lowering installation cost
• Rugged durable material suitable for onsite or offsite applications
• LEED compliant, low VOC
• Low outgassing properties for clean room environments