logo

Altra~Lock 576

A rapid dry/quick cure 100% solids penetrating epoxy sealer designed for use where less than ideal surface preparation is attainable or where surfaces have inherent porosity or surface weakness. It has a very low viscosity which allows it to wick into and bond porous substrates and residual rust into a tough epoxy composite. It may be applied to residual rust, degraded or new concrete, fibre-reinforced cement, and timber.

FEATURES:

  • Excellent wetting properties
  • 100% solids
  • Rapid cure
  • Low temperature cure as low as 4°C
  • Ideal for marginally prepared steel
  • Easy application by brush, roller, or low atomisation spray
  • Can be used to seal asbestos
  • Suitable for below waterline applications on marine vessels when used underneath a high build epoxy barrier system
  • Approved for use in food & dairy processing plants

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Carboguard 635 HAR

An all-purpose epoxy that has a variety of attributes including low-temperature cure, surface tolerance, fast recoat times, moisture tolerance during application and cure, and excellent corrosion protection. Carboguard 635 HAR can be used direct to metal as a corrosion resistant primer or as an intermediate coating over other primers. It is suitable for both maintenance and new construction projects due to its excellent surface wetting characteristics and quick cure for handling. It may also be used for immersion in fresh or salt water (marine) exposures and exhibits exceptional abrasion  resistance & toughness.

FEATURES:

  • Low temperature cure -7°C (20°F)
  • Excellent corrosion protection
  • High abrasion resistance
  • Excellent flexibility
  • Excellent application characteristics
  • Fast recoat times
  • Moisture tolerance during application
  • Extended re-coat window for atmospheric exposures up to 6 months self re-coat
  • Approved for use in food & dairy processing plants

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Carboguard 636 PW

Made to Order or imported lines subject to availability.

High performance immersion grade epoxy that is designed as a liner for potable water tanks. This coating exhibits moisture tolerance during application, low temperature cure capability, and fast cure response for quick return to service. Product is self-priming on steel and is normally applied in two coats. Formulated for application at 120 to 180 microns DFT per coat for potable use.

FEATURES:

  • Very good flexibility – resists chipping and aged embrittlement
  • Lighter weight – 13% lighter than most similar coatings
  • Versatile surface tolerant coating
  • AS/NZS 4020 Potable Water Approval
  • Lower viscosity allows application at higher solids (less thinning) and reduced VOC at application
  • Fast dry to recoat
  • Low temperature cure to below freezing; -5°C
  • Reduced HAPS and Low VOC

 

Availability :- New Zealand

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Carboguard 636 XT

A multi-purpose, advanced technology coating suited to marine and industrial applications. Suitable for atmospheric and many immersion exposures. The DTM properties make it a versatile coating in maintenance and new work applications. Syntactic foam modification gives it unique thermal shock resistance and flexibility.

FEATURES:

  • Very good flexibility – resists chipping and aged embrittlement
  • Versatile surface tolerant coating
  • Suitable for application over surfaces prepared by water-jetting
  • Good adhesion to tight rust - especially when used in conjunction with Rustbond PS or Altra~Lock 576
  • Tolerant to surface dampness - particularly when brush/roller applied
  • Self-priming (DTM) for many applications
  • Fast dry to recoat
  • Excellent dry to handling properties
  • Suitable for fresh and salt water immersion
  • Low temperature cure to below freezing; down to -5°C
  • Reduced HAPS and Low VOC
  • Cleaner colours and improved colour stability

Availability :

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Carboguard 636 XT GF

A glass-flake filled, multi-purpose,advanced technology coating suited to marine and industrial applications. Suitable for atmospheric and many immersion exposures. The DTM properties make it a versatile coating in maintenance and new work applications. Syntactic foam modification gives it unique thermal shock resistance and flexibility. Glass flake reinforcement enhances film strength, impact resistance and barrier properties.

FEATURES:

  • Excellent physical and barrier properties
  • Versatile surface tolerant coating
  • Good adhesion to tight rust - especially when used in conjunction with Rustbond PS or Altra~Lock 576
  • Tolerant to surface dampness - particularly when brush/roller applied
  • Fast dry to recoat
  • Excellent dry to handling properties
  • Suitable for fresh and salt water immersion
  • Low temperature cure to below freezing; down to -5°C
  • Reduced HAPS and low VOC
  • Cleaner colours and improved colour stability

Availability :

View More Product Data Sheet 

Carboguard 696 HBE

Made to Order or imported lines subject to availability. 

Suitable for single coat applications in areas such as a penstock lining at film thicknesses ranging between 400 and 1500 microns. Suitable for service in various immersion environments including industrial wastewater, slurry tanks, sea or fresh water, on buried structures, and on high wear surfaces in atmospheric exposure.

FEATURES:

  • High film builds in a single coat – 0.4mm to 1.5mm
  • Extensive case history in hydro penstocks & scroll casings, along with industrial wastewater processing
  • Positive cure, even at low temperatures
  • Highly abrasion resistant
  • Unique flexibilised formulation imparts excellent impact resistance
  • May be used on buried structures, structures immersed in fresh or salt water, and for atmospheric exposure
  • Suitable for use with cathodic protection systems – impressed current or anode types
  • Easy application qualities using properly heavy-duty airless spray equipment

 

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Carbomastic 615

High performance epoxy that has excellent resistance to fresh and salt water exposures. This coating exhibits outstanding moisture and surface tolerance during application, low temperature cure capability, and very fast cure response for quick return to service. It contains an inert flake reinforcement (micaceous iron oxide) to enhance film strength and performance. This product is ideal for industrial or heavy duty marine environments for the protection of steel against salt laden environments.

FEATURES:

  • High solids, low VOC
  • Low temperature cure
  • Excellent wetting properties
  • Excellent surface tolerance
  • Excellent moisture tolerance (application)
  • Fast cure response
  • Suitable for immersion service in fresh or salt water after 60 minute cure at 24°C
  • Approved for use in food & dairy processing plants

 

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Carbothane 133 LH

High build, low sheen finish that has excellent resistance to corrosion, chemicals and abrasion. Suitable for application over a number of Carboline primers and intermediates, this material provides very good weathering performance in a broad range of colours

FEATURES:

  • Outstanding performance properties in both mild and aggressive environments
  • High build; suitable for many two-coat systems
  • Approved for use in food & dairy processing plants
  • Application by spray, brush or roller
  • Indefinite recoatability
  • VOC compliant to current AIM regulations

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Carbothane 134 HG

Thin film, high gloss finish with exceptional weathering performance characteristics. Used extensively in virtually all industrial markets, Carbothane 134 HG provides a smooth, durable finish that has superior resistance to corrosion, abrasion and chemical exposure.

FEATURES:

  • High solids, low VOC content
  • Excellent weatherability
  • Exceeds SSPC Paint 36 specification for a Level 3 urethane
  • Conforms to the requirements of AS/NZS 3750.6:2009, Type 1 "Paints for Steel Structures - Full Gloss Polyurethane (two pack)"
  • Approved for use in food & dairy processing plants (refer to "Approvals NZ/AU" section)
  • Very good aged re-coatability
  • Excellent flow characteristics allow for application by spray or roller
  • Superior impact and abrasion resistance
  • Indefinite recoatability

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Carboxane 2000

Made to Order or imported lines subject to availability.

Carboxane 2000 is an isocyanate-free, ultra-durable coating that provides outstanding colour and gloss retention as well as excellent corrosion protection for exterior exposures. When used over a suitable primer (as a two coat system) Carboxane 2000 provides the barrier, corrosion resistance properties, and weatherability normally achieved with a three-coat system (primer, epoxy intermediate with an acrylic-polyurethane finish) for most environments. This significantly speeds up the painting process, saves labour, and saves money without sacrificing performance. This tightly cross-linked film utilises a UV-resistant siloxane binder resulting in a finish with excellent corrosion protection and weathering performance that far exceeds aliphatic polyurethanes.

FEATURES:

  • Isocyanate free
  • Exceptional weatherability
  • Outstanding colour and gloss retention
  • Exceeds SSPC Coating Specification No. 36 Level 3A
  • Excellent corrosion protection
  • Meets ISO 12944 C3 High and C4 Medium, one coat applied at 125 to 175 microns DFT
  • High build, 75 to 175 microns DFT
  • Saves significant time, labour, and money
  • Long service life
  • VOC compliant
  • Excellent durability
  • Good flexibility and abrasion resistance
  • Long pot life

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Carbozinc 11

Time-tested corrosion resistant primer that provides excellent corrosion protection to steel in some of the harshest environments. For over five decades, Carbozinc 11 has been the industry standard for high-performance inorganic zinc protection on steel structures worldwide.

FEATURES:

  • Meets Class B slip co-efficient and creep testing criteria for use on faying surfaces
  • Rapid cure. Dry to handle in 45 minutes at 16°C (60°F) and 50% relative humidity
  • Low temperature cure down to -18°C
  • High zinc loading
  • Meets FDA requirements
  • Zinc supplied meets ASTM D520 (Type II)
  • Meets SSPC Paint 20 Type I, Level 1 for zinc content
  • Complies with the composition and performance requirements of AS/NZS 3750.15, Type 4 and AS 4848.1 "Single Coat Inorganic Zinc Silicate"
  • Very good resistance to salting
  • May be applied with standard airless or conventional spray equipment
  • Approved for use in food & dairy processing plants

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Carbozinc 11 WB

Made to Order or imported lines subject to availability.

Carbozinc 11 WB is a water-based inorganic zinc rich primer that protects steel galvanically, eliminating subfilm corrosion. It meets VOC regulations while providing the proven performance of silicate zinc rich technology. It may be used as a primer under many different types of topcoats.

FEATURES:

  • Excellent corrosion protection
  • High zinc loading per square foot
  • Zero VOC
  • Good resistance to salting
  • Fast curing, quick handling
  • Excellent application characteristics (less likely to pump packing or tip plugging)
  • Meets Class B slip coefficient* and creep testing criteria for use on faying surfaces
  • Conforms to AS/NZS 3750.15 Type 3

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Carbozinc 15-625

A high performance, two component, organic zinc-filled primer specifically formulated to provide corrosion protection to steel surfaces in salt and weathering environments. It has good surface tolerant characteristics where steel surface preparation may be less than ideal. It may also be used for the repair of aged inorganic zinc-rich coatings or galvanised steel surfaces.

FEATURES:

  • Exceptional corrosion resistance
  • Extremely high zinc loading - 90% by weight in dry film
  • Provides excellent cathodic protection
  • Excellent adhesion to commercial blast cleaned surfaces
  • Excellent for repairs to inorganic zinc silicate primers and aged/deteriorated galvanising
  • Meets the requirements of AS/NZS 3750.9, Type 2 Organic Zinc Rich
  • Conforms to the composition and performance requirements of SSPC-Paint 20 Type II Organic
  • As a brush applied maintenance primer tolerant to traces of surface moisture
  • As a holding / weld-through primer when applied less than 25 microns dry

Availability :

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Carbozinc 858

NEW 4:1 Ratio

A high-solids, zinc-filled epoxy primer for corrosion protection of structural steel in salt and weathering environments. This high performance primer has quick cure-to-topcoat characteristics for in-shop applications and quick turnaround requirements in the field. It has excellent adhesion and undercutting resistance and is outstanding for use as a corrosion resistant primer for a variety of applications.

FEATURES:

  • Protects steel galvanically
  • Outstanding application properties
  • Cures at low temperatures down to 2ºC
  • Complies with AS 3750.9:1994 Type 2 Organic Zinc Rich
  • Suitable for application over Wet Abrasive Blast cleaned surfaces
  • Protects against corrosion under-cutting
  • Tough and abrasion resistant film
  • Ideal for severe industrial or marine environments with appropriate topcoats
  • Approved for use in food & dairy processing plants

Availability :

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Carbozinc 859 EZ2

A two-component, high solids, zinc rich epoxy primer formulated for the protection of properly prepared steel substrates. Carbozinc 859 EZ2 can be applied by conventional or airless spray. Recommended where a high performance, highly corrosion resistant zinc primer is desired. Typical applications include structural steel, tanks, piping, equipment and other miscellaneous parts in industrial or architectural projects.

FEATURES:

  • Excellent application properties
  • Tough abrasion resistant film
  • Excellent adhesion & undercutting resistance
  • Superior corrosion resistance
  • Meets VOC (Volatile Organic Content) regulations, <335 g/litre
  • Fast drying for recoat
  • Meets or exceeds SSPC Paint System 20 Level 3 (2002)
  • Excellent film forming properties eliminate topcoat blistering
  • Excellent resistance to salting on weathering exposure

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Chem~Bar 3500

A single pack steel primer designed for use in industrial and marine applications

FEATURES:

  • Single pack direct to steel primer
  • Excellent corrosion protection
  • Fast dry time
  • Excellent application properties
  • Excellent water immersion resistance
  • Reinforced with aluminium flake
  • Cost effective & easy to use product for dockings
  • Simplified coating system for maintenance repaints in the commercial marine sector
  • Extended time to overcoat with antifoulings
  • A barrier/seal coat over aged or incompatible/unknown antifoulings or a tie coat over suitably prepared, aged epoxy coatings prior to application of the selected Sea~Barrier antifouling
  • A sealant to assist in the prevention of TBT leaching from an underlying antifouling coating - provided it is applied at a minimum dry film thickness of 80 microns (minimum 2 coats by roller)
  • Supported by many case histories within the commercial marine market over sequential dockings

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Chem~Bar 900

Specifically formulated to protect metal or masonry surfaces exposed to weather, water or chemicals.
Chem~Bar 900 may be used to protect structural steel, tanks, pipes and equipment in the following:

  • Pulp and Paper Industry
  • Chemical Process Industry
  • Sewage and Wastewater Plants
  • Water Tanks
  • Refineries
  • Fertiliser Plants
  • Marine Installations
  • Bridges
  • Power Projects
  • Shipping Containers

FEATURES:

  • Can be used as a finish coat on a wide variety of primers, including Altex or Carboline high performance two pack primers and epoxies
  • Self-priming on steel
  • Can be built to 125 microns DFT
  • Quick dry - even at low temperatures
  • Good resistance to inorganic acids, salt solutions, alkalis, and gases
  • Excellent adhesion to aged chlorinated rubber coatings
  • Excellent recoatability, even after years of weathering
  • Excellent colour retention
  • Resists excessive chalking
  • Available in Aluminium Finish and Metal-Spray Sealer – refer to Chem~Bar 900 Aluminium PDS

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Chem~Bar 900 Aluminium

A specialised variant of the well-proven Chem~Bar 900. A high-performance aluminium-filled vinyl acrylic suitable for use as a general-purpose aluminium finish and for sealing thermal metal spray.

Chem~Bar 900 Aluminium may be used in all atmospheric exposures where traditional aluminium finishes may be employed; including:

  • Pulp and Paper Industry
  • Chemical Process Industry
  • Sewage and Waste Water Plants
  • Water Tank & Silo Exteriors
  • Refineries
  • Fertiliser Plants
  • Marine Installations
  • Bridges
  • Power Projects
  • Shipping Containers

FEATURES:

  • Developed from proven technology
  • Quality aluminium finish
  • Designed for use as a sealer over: zinc metal spray, zinc/aluminium 95/5 metal spray, aluminium metal spray
  • Improves the appearance of metal spray
  • Increases the performance life of metal spray
  • Long term self-recoatability with minimal surface preparation

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

E~Line 379

High gloss, high performance, two component, chemically cured polyaspartic urethane designed for use in areas where maximum gloss and colour retention are required.

FEATURES:

  • Polyaspartic acrylic technology provides exceptional gloss and colour retention
  • Outstanding cosmetic properties
  • Outstanding abrasion resistance
  • Excellent durability due to high flexibility and toughness
  • Exceptional retention of cosmetic properties due to high UV resistance
  • Outstanding chemical resistance
  • Light colours along with a finish coat of Carbothane 130 Clear Coat may be used as an anti-graffiti system due to the excellent solvent resistance - refer also to and Easy~Clean SX Additive
  • High volume solids - Low VOC
  • Available with Ultra-Fresh Antimicrobial Additive where hygienic germ-free coating systems are required.
  • Tested and in compliance to Main Roads WA - Specification 908 and NZTA (Waka Kotahi) - Specification S10 for Anti-Graffiti Coatings
  • Approved for use in food & dairy processing plants

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Filler #50

Graded silica blend for epoxy putty / mortar mixes

Availability :

View More NZ Safety Data Sheet Aus. Safety Data Sheet

Glass Flake Additive

Reinforcing additive for a range of Carboguard epoxy coatings

Availability :

View More NZ Safety Data Sheet Aus. Safety Data Sheet

Phenoline 1205

Made to Order or imported lines subject to availability. 

Glass flake-filled coating with dense cross-linking that exhibits excellent overall chemical resistance to a variety of aggressive chemicals. Glass reinforcement provides added abrasion resistance, permeation resistance and internal reinforcement. 1205 exhibits very good acid resistance. Excellent for use as a lining for tanks or pipes in process facilities where hot water or abrasive conditions exist.

FEATURES:

  • Excellent resistance to ethanol, gasoline, jet fuels and solvents
  • Excellent abrasion resistance
  • Excellent thermal shock resistance (-17 to 150°C)
  • Excellent resistance to deionized or demineralised water up to 95°C
  • Excellent resistance to crude oil up to 121°C
  • Excellent for crude oil storage and transportation up to 121°C
  • Recommended for CS-1,3,4 and SS-1,2,3 systems of NACE SP0198 Standard Practice for coatings to control Corrosion Under Insulation (CUI)
  • Approved for use in food & dairy processing plants

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Phenoline 353 LT

Made to Order or imported lines subject to availability.

Phenoline 353 LT is a highly cross-linked epoxy lining with extraordinary overall chemical resistance and versatility. It has a unique blend of resins that make it highly resistant to a variety of aggressive cargoes like gasoline, gasoline blends, biodiesel, fuel oils, and others. It can be used in both acidic and high temperature caustic exposures. Markets served are terminals, refineries, petrochemical, wastewater, railcar linings, subsea oil and gas equipment, and many others. This low temperature cure formulation allows application and curing down to 2°C.

FEATURES:

  • Outstanding overall chemical resistance
  • Dense, highly cross-linked film for superior barrier protection
  • Excellent abrasion resistance and toughness
  • Well-suited for hydrocarbon exposures
  • Cures down to 2°C
  • Meets NORSOK System 7C requirements for subsea equipment up to 180°C
  • Approved for use in food & dairy processing plants

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Phenoline Tank Shield

Made to Order or imported lines subject to availability. 

This product is a solvent-free, high performance epoxy coating designed as an internal tank, valve and pipe lining for chemical or other commodity storage. It is a unique blend of resins and curing agents that allow batch mixing for ease of application. Plural component spray equipment is not required. The product is blush resistant and is typically applied at film thicknesses of 500 microns or thicker as needed (tank floors). It can handle exposures typically seen in the oil and gas industries; crude oils and fuels. It is resistant to NGL condensates, produced water, brines, industrial process water, waste water, and sewage. Ideal for municipal wastewater and water treatment facilities.

FEATURES:

  • Batch mix formulation, single leg airless spray
  • High impact resistance
  • Superior adhesion to steel
  • Excellent resistance to water and salt water
  • Resistance to a broad range of fuels including ethanol
  • Passes EI 1541 requirements for internal protective coating systems used in aviation fuel handling systems, including the jet fuel gum test
  • Resistant to hot water up to 82°C
  • Excellent abrasion resistance and flexibility
  • Can be applied down to 2°C
  • Can be applied as a single or multi-coat system
  • NSF/ANSI 61 compliant for use in potable water tanks, pipes, and valves.*
  • Certified by UL to meet the drinking water criteria of NSF/ANSI/CAN 600
  • Non-blushing with a long recoat window
  • Tested and approved to AS/NZS 4020:2018
  • Low odour

Contact Carboline Technical Service for approved dimensions.
*Valid when manufactured at a certified location.

Availability :

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Phenoline Tank Shield FP

Made to Order or imported lines subject to availability.

This product is a solvent-free, high performance epoxy coating specifically designed as a pit filling primer with ideal flow properties allowing it to wet-out and fill moderate to severe pitting on steel tank bottoms. It's unique formula allows batch mixing for ease of application. With an appropriate lining, it can withstand exposures typically seen in the oil and gas industries. It is resistant to crude oil, NGL condensates, produced water, brines, and industrial process water.

FEATURES:

  • Highly penetrating formula to handle severe pitting
  • Blast hold protection
  • Batch mix formulation, single leg airless spray
  • Superior adhesion to steel
  • Excellent abrasion resistance and flexibility
  • Can be applied down to 2°C
  • Can be used with multiple lining systems
  • Non-blushing with a long recoat window
  • Convenient packaging for batch mix
  • Tested and approved to AS/NZS 4020:2018 when topcoated with Phenoline Tank Shield (refer to data sheet)
  • Low odour

Availability :

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Pyrocrete 241

Made to Order or imported lines subject to availability.

A 55 lb./ft³ (881 kg/m³) density, Portland cement based, cementitious fireproofing. It provides bothhydro carbon and cellulosic fire protection for structural steel and can also be used to upgrade the fire resistance of existing concrete. Recommended areas of application include refineries, petrochemical, pharmaceutical facilities, pulp and paper mills, offshore platforms, nuclear and conventional power plants, factories, warehouses, institutional and biomedical facilities.

FEATURES:

  • Over 40 years of proven performance
  • Exceptional durability and toughness
  • Tested and approved for exterior use by Underwriters Laboratories Inc
  • UL 1709 hydrocarbon fire rated up to 4 hours
  • BS 476 hydrocarbon fire rated up to 4 hours
  • ISO 22899-1 jet fire rated up to 2 hours
  • ASTM E119 cellulosic fire rated up to 4 hours
  • Cryogenic protection against LNG spills and immersion exposures
  • Resistant to 3 bar blast overpressure
  • Hose stream resistant
  • Tolerant to wide range of climates
  • Lightweight – one-fifth the weight of concrete for equal fire protection
  • Ideal for onsite and offsite application
  • Easy application by spray or trowel
  • Nonflammable – during or after application
  • Chloride and sulfide free – no special priming required
  • Asbestos-free – complies with EPA and OSHA regulations
  • Non-friable – high impact strength

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Reactamine 760 HB

Made to Order or imported lines subject to availability.

Environmentally friendly, advanced hybrid technology, plural-component applied coating used as a lining for water, wastewater, manholes, penstocks, dam gates, pipelines and other aggressive immersion applications. Provides protection against microbiologically induced corrosion (MIC) and hydrogen sulfide corrosion found in wastewater treatment service. Ultra high build product designed to be applied at high thickness in one coat application. 

FEATURES:

  • High film build (5000 microns / 5mm plus) in one coat
  • Complies with Greenbook
  • UL approved for potable water*
  • Cold temperature cure
  • Fast cure and walk on time
  • Excellent barrier properties, low permeability
  • Can be used to resurface highly deteriorated concrete
  • Bridges normal shrinkage cracks in concrete
  • True monolithic film on steel and concrete
  • Encapsulates rivets, bolts, and edges in one coat
  • Outstanding abrasion, impact and tear resistance
  • Combines polyurethane and polyurea technologies to form a hybrid polyurethane

*Valid if manufactured at a certified location.

Availability :

View More Product Data Sheet NZ Safety Data Sheet 

Rustbond PS

Rustbond PS is a very low VOC epoxy primer/sealer that combines outstanding surface tolerance characteristics over marginally prepared substrates and user-friendly features. It accepts a variety of topcoats and can help save time and money by minimising surface preparation requirements for new construction, maintenance and overcoating projects. Rustbond PS has good pot life at higher temperatures to help minimise waste and also cures at low temperatures down to 1.7°C with Epoxy Accelerator so you have one Rustbond product for year-round application.

FEATURES:

  • Excellent wicking characteristics resulting in very good adhesion to a variety of substrates
  • Low stress during application and cure, can be applied over aged coatings and tight rust
  • Universal primer and tie-coat
  • Very low VOC, less than 100 g/l, and low odour for compliance in many stringent locations
  • Low temperature cure with Epoxy Accelerator to extend the painting season
  • Good pot life in hotter weather without Epoxy Accelerator, one Rustbond PS for year-round application
  • User-friendly application with brush, roller, and spray
  • Tolerates higher dry film thickness (DFT) range, easier to apply
  • Excellent sealer for metallising and thermal sprayed aluminium (TSA)

Availability :

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Thermaline 4900 Aluminium

Air-dried coating suitable for high temperature exposures up to 273°C (525°F). Air-drying characteristics allow for faster handling of in-shop applications than with other high-temperature coatings. Heat cure above 150°C (300°F) is recommended and will impart added strength and integrity to the coating.

FEATURES:

  • Temperature resistance up to 273°C (525°F)
  • Single-coat application
  • Excellent resistance to thermal shock
  • Good weathering and colour stability

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Thermaline Heat Shield

Made to order or imported product subject to availability.

This is an extreme performance coating for hot, cryogenic and cycling exposures. Thermaline Heat Shield contains a unique blend of plate-like reinforcing pigments fortified with an inert polymeric matrix. The resulting film provides an outstanding barrier against corrosives and harsh exposures typically seen in elevated temperature environments. This versatile coating is ideal for all piping, vessels and equipment operating from cryogenic conditions up to 650°C (1200°F). It is particularly well suited to prevent corrosion under insulated equipment/piping for both carbon steel substrates and stainless steels. This fortified coating has superior shop handling properties over standard silicone coatings (see Curing). It is recommended for CS-6 and SS-5 systems of NACE SP0198 Standard Practice for coatings to control corrosion under insulation (CUI).

FEATURES:

  • Unique reinforced but flexible polymer film
  • Versatile use from cryogenic to 650°C (1200°F) exposures
  • Dries to handle without heat cure (See curing schedule)
  • Outstanding barrier properties
  • Protects steel from thermal wet cyclic conditions
  • Suitable for both shop and field application
  • Provides corrosion protection even with ambient temperature cure
  • Self priming or apply over Carbozinc 11 primers when uninsulated
  • Protects stainless steels from chlorides and stress corrosion cracking
  • Very fast recoat times

Availability :

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Thermo-Lag 3000-SP

Made to Order or imported lines subject to availability.

Certified Applicators Only. Applicator Note: Thermo-Lag 3000-SP may only be applied by trained and approved applicators; refer to Altex Coatings for approved applicator listings in your area.

Thermo-Lag 3000-SP is a flexible, two-component epoxy Intumescent Fireproofing coating designed to provide asset integrity from the damaging effects of hydrocarbon fires. Since 1999 Thermo-Lag 3000-SP has provided fire protection in the harshest of environments, such as oil, gas, refineries, power, marine, petrochemical, and LNG facilities.
Thermo-Lag 3000-SP has been extensively and independently tested in accordance with: UL 1709, UL 2431 Category I-A, ISO 834-3, IMO FTP Code (IMO A.754(18) for H-0, H-60 & H-120 Divisions, ASTM E84, ASTM E119, ISO 20340, NORSOK M-501 5A Fire and Corrosion Testing, and NFPA 290 (extended to 150 minutes).

FEATURES:

  • Provides a flexible fire protection solution to structural steelwork, process vessels, divisions and electrical raceways for 1 through 4 hours
  • Lowest thickness per fire rating of any competitive epoxy intumescent coating
  • Durable finish – provides a hard, durable finish resistant to normal wear & tear.
  • Inherently flexible and durable formulation designed to withstand abrasion, vibration, handling, transportation and erection stresses in any climate.
  • Formulated to maintain it’s flexibility, elongation and fire resistive properties throughout its service life regardless of climate.
  • Engineered to resist extreme and rapid temperature cycles without cracking or disbondment.

Availability :- New Zealand- Australia

View More Product Data Sheet NZ Safety Data Sheet Aus. Safety Data Sheet

Offline

* Sorry, we aren’t online at the moment. Please fill out the form below and we will get back to you as soon as possible.