Made to Order or imported lines subject to availability.

Altra~Shield® WB-V is a two pack low VOC waterborne epoxy. The cured film presents a non-yellowing finish with high surface hardness and excellent flexibility. It exhibits excellent adhesion and water resistance, and is tolerant of application over damp surfaces. 

Self-priming over concrete, plaster and fibre cement substrates

• Very good abrasion resistance
• Excellent solvent resistance (when fully cured)
• Excellent resistance to alkalis
• Fair resistance to acids
• Resistant to common CIP chemicals & typical dairy processing by-product exposures as follows:
  • Nitric Acid 5% - 15 hr watch-glass - pass*
  • Sodium Hydroxide 5% - 26 hr watch-glass - pass*
  • Lactic Acid 5% - 26 hr watch-glass - pass*

Made to Order - High performance immersion grade epoxy that is designed as a liner for potable water tanks. This coating exhibits moisture tolerance during application, low temperature cure capability, and fast cure response for quick return to service.
Product is self-priming on steel and is normally applied in two coats. Formulated for application at 120 to 180 microns DFT per coat for potable use.

• Very good flexibility – resists chipping and aged embrittlement
• Lighter weight – 13% lighter than most similar coatings
• Versatile surface tolerant coating
• AS/NZS 4020 Potable Water Approval (see "Approvals NZ/AU" section)
• Lower viscosity allows application at higher solids (less thinning) and reduced VOC at application
• Fast dry to recoat
• Low temperature cure to below freezing; -5°C
• Reduced HAPS and Low VOC

A multi-purpose, advanced technology coating suited to marine and industrial applications. Suitable for atmospheric and many immersion exposures. The DTM properties make it a versatile coating in maintenance and new work applications. Syntactic foam modification gives it unique thermal shock resistance and flexibility.

Link

A glass-flake filled, multi-purpose,advanced technology coating suited to marine and industrial applications. Suitable for atmospheric and many immersion exposures. The DTM properties make it a versatile coating in maintenance and new work applications. Syntactic foam modification gives it unique thermal shock resistance and flexibility. Glass flake reinforcement enhances film strength,
impact resistance and barrier properties.

Aliphatic Acrylic-Polyester Polyurethane Satin Finish

High build, low sheen finish that has excellent resistance to corrosion, chemicals and abrasion. Suitable for application over a number of Carboline primers and intermediates, this material provides very good weathering performance in a broad range of colours

• Outstanding performance properties in both mild and aggressive environments
• High build; suitable for many two-coat systems
• Approved for use in food & dairy processing plants
• Application by spray, brush or roller
• Indefinite recoatability
• VOC compliant to current AIM regulations

High gloss polyurethane finish with exceptional weathering performance characteristics.

Used extensively in virtually every market sector, including marine exposure, Carbothane 134 HG provides a smooth, durable finish that has superior resistance to corrosion, abrasion and chemical exposure.

• Specialised UV protection designed for Australian and New Zealand exposures
• Highly recoatable, with minimum preparation requirements
• The high solids (70%) formulation creates a very cost effective coating

E~Line 379® is a high gloss, high performance, two component, chemically cured polyaspartic urethane designed for use in areas where maximum gloss and colour retention are required.

E~Line 379® will provide excellent gloss and colour retention as well as resistance to moderate to severe corrosive environments for:

• Transportation industry
• Chemical processing industry
• Pulp and paper industry
• Dairy industry
• Bridges and storage tanks
• Light colours and clear may be used as anti-graffiti coatings due to their excellent solvent resistance - refer also to Altex Graffiti Remover and Easy~Clean SX Additive
• Outstanding abrasion resistance
• Excellent durability due to high flexibility and toughness
• Exceptional tolerance to marginal application conditions
• Exceptional retention of cosmetic properties due to high UV resistance

Made to Order or imported lines subject to availability. 

A glass flake-filled coating with dense cross-linking that exhibits excellent overall chemical resistance to a variety of aggressive chemicals. Glass reinforcement provides added abrasion resistance, permeation resistance and internal reinforcement.

Phenoline® 1205 exhibits very good acid resistance. Excellent for lining tanks or pipes in process facilities where hot water or abrasive conditions exist. Also used as a primary or secondary containment lining for a variety of aggressive chemicals

• Excellent resistance to ethanol, gasoline, jet fuels and solvents
• Excellent abrasion resistance
• Excellent thermal shock resistance
• Excellent resistance to deionized or demineralised water up to 82°C
• Excellent resistance to crude oil, brine or water up to 93°C

Made to Order or imported lines subject to availability. 

Reactamine Joint Seal FC is a 2-component 100% solids, polyurea-based joint sealant that is self-leveling and cures in approximately 30 minutes. It works equally well with asphalt and concrete and protects interior horizontal concrete expansion and control joints from spalling, chipping and breakdown. This product can be applied at temperatures ranging from -18° to 65°C and possesses excellent chemical resistance, water resistance and thermal stability at both high and low temperatures

Rustbond PS is a very low VOC epoxy primer/sealer that combines outstanding surface tolerance characteristics over marginally prepared substrates and user-friendly features. It accepts a variety of topcoats and can help save time and money by minimising surface preparation requirements for new construction, maintenance and overcoating projects. Rustbond PS has good pot life at higher
temperatures to help minimise waste and also cures at low temperatures down to 1.7°C with Epoxy Accelerator so you have one Rustbond product for year-round application.